Influence of Thermo-Mechanical Processing on Microstructure, Mechanical Properties and Corrosion Behavior of Ti-6Al-6Mo Implant Alloy

Kartika, Ika; Rokhmanto, Fendy; Thaha, Yudi Nugraha; Purawiardi, Ibrahim; Astawa, I Nyoman Gede Putrayasa; Erryani, Aprilia; Asmaria, Talitha

doi:10.1007/978-981-33-6926-9_34

Cited by 2 publications

(1 citation statement)

References 12 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The supply of an adequate quantity of powders for 3D printing of titanium components has been a challenge in underdeveloped countries due to the rapid increase in the demand for these powders by different manufacturing industries in the developed countries. Another setback associated with Ti alloys' use for thermomechanical processes is the heterogeneous nature of 3D printed ingots [148,149,150]. This led to an increase in the distribution of the alloying elements between the top, base and across the diameter of the fabricated shapes.…”

Section: Challenges and Prospects For Titanium-based Alloysmentioning

confidence: 99%

Additive manufacturing of titanium-based alloys- A review of methods, properties, challenges, and prospects

Tshephe

Akinwamide

Olevsky

et al. 2022

Heliyon

136

View full text Add to dashboard Cite

Section: Challenges and Prospects For Titanium-based Alloysmentioning

confidence: 99%

Additive manufacturing of titanium-based alloys- A review of methods, properties, challenges, and prospects

Tshephe

Akinwamide

Olevsky

et al. 2022

Heliyon

136

View full text Add to dashboard Cite

Effect of Heat Treatment on Some Titanium Alloys Used as Biomaterials

et al. 2022

View full text Add to dashboard Cite

Titanium-based alloys are constantly improved to obtain properties suitable for their use. Improving titanium alloys is very important for performing alloys without side effects. In this paper effects of structure, microhardness, and indentation test of eight titanium alloys were investigated after aging. The heat treatment consisted of a high-temperature quenching accomplished in three steps (650 °C for 25 min, 850 °C for 20 min, and 950 °C for 20 min). The cooling process was accomplished using N2 gas, introduced in the chamber at a 9-bar pressure for 37 min. Then, followed by heating to a constant temperature tempering (550 °C) at 1.5 bar pressure and kept for 2 h and 10 min at 2 bar pressure. Optical microscopy images were obtained of Ti-Mo-Zr-Ta alloys with grain-specific aspects of titanium alloys; acicular and coarse structures are specific to β alloys. Microhardness results showed significantly influenced by the heat treatment, increased by approximately 5% for Ti15Mo7Zr15Ta1Si and Ti20Mo7Zr15Ta0.5Si, while for Ti15Mo7Zr15Ta0.5Si and Ti20Mo7Zr15Ta an approximately 9% decrease has been noted. The modulus of elasticity results obtained by the indentation method for the experimental alloys were between 36.25–66.24 GPa. The heat treatments applied to the alloys had a pronounced effect, improving both the structure of the alloys and the results of the indentation test.

show abstract

Influence of Thermo-Mechanical Processing on Microstructure, Mechanical Properties and Corrosion Behavior of Ti-6Al-6Mo Implant Alloy

Cited by 2 publications

References 12 publications

Additive manufacturing of titanium-based alloys- A review of methods, properties, challenges, and prospects

Additive manufacturing of titanium-based alloys- A review of methods, properties, challenges, and prospects

Effect of Heat Treatment on Some Titanium Alloys Used as Biomaterials

Contact Info

Product

Resources

About