MATLAB-Arduino as a low cost microcontroller for 3 phase inverter

Zulkifli, Shamsul Aizam; Hussin, Mohd Najib; Saad, Abdul Salam

doi:10.1109/scored.2014.7072980

Cited by 17 publications

(10 citation statements)

References 9 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The feedback controller maintains a constant load voltage via the proper tuning of the PI parameters by using the LSA optimization method [23]. An Arduino microcontroller board is used to generate the gate control signals to drive the inverter [24]. Finally, a low pass filter is connected at the load side to eliminate the high frequency components in the output voltage and thereby improve the output quality.…”

Section: Operation Of the Proposed Voltage-frequency Convertermentioning

confidence: 99%

Universal power converter for low power applications

Asna¹,

Shareef²,

Khalid³

et al. 2019

IJPEDS

View full text Add to dashboard Cite

A novel power converter that can perform both voltage and frequency conversion was proposed. Inappropriate power supply can damage sensitive sub-components and render the connected device inoperable. Henceforth, the proposed voltage–frequency converter acts as an interface to plug any electrical device directly into an electrical socket and provide the voltage and frequency required. The converter used a synchronous reference frame proportional–integral (SRFPI) controller to regulate the instantaneous output voltage and to improve steady state performance. Because the PI controller works together with the synchronous reference frame controller, it is difficult to tune the PI control parameters. To overcome this issue, a new meta heuristic optimization technique called lightening search algorithm (LSA) optimization was used to identify the optimum PI parameter values. A detailed description of the system operation and control strategy was presented. Finally, the performance of the converter was analyzed and verified by simulation and experimental results. The experimental result has shown that the proposed system has satisfactory output voltage and frequency under different input voltages.

show abstract

Section: Operation Of the Proposed Voltage-frequency Convertermentioning

confidence: 99%

Universal power converter for low power applications

Asna¹,

Shareef²,

Khalid³

et al. 2019

IJPEDS

View full text Add to dashboard Cite

show abstract

“…Then, the Arduino Uno must have coding for it to function as desired. Lastly, the LCD is to display the output that have written in the coding inside the Arduino Uno [22][23]. Fig.…”

Section: Light Sensormentioning

confidence: 99%

Solar Energy Measurement Using Arduino

Jumaat

Othman

2018

MATEC Web of Conferences

View full text Add to dashboard Cite

Abstract. This project aims to develop a measurement of solar energy using Arduino Board technology. In this research, four parameters that been measured are temperature, light intensity, voltage and current. The temperature was measured using temperature sensor. The light intensity was measured using light dependent resistor (LDR) sensor. The voltage was measured using the voltage divider because the voltage generated by the solar panel are large for the Arduino as receiver. Lastly for the current was measured using the current sensor module that can sense the current generated by the solar panel. These parameters as the input value for the Arduino and the output was display at the Liquid Crystal Display (LCD) screen. The LCD screen display output of the temperature, the light intensity, the voltage and the current value. The purpose of Arduino to convert the analog input of parameter to the digital output and display via LCD screen. Other than that, this project also involve with a design to ensure that device case are easy to be carry around.

show abstract

“…This study presents with a fly converter controller by Arduino Uno board. It has been selected because of its simplicity in use (Zulkifli et al, 2014;Badamasi, 2014). In this study, PI controller is achieve by programming of Arduino Uno board.…”

Section: Introductionmentioning

confidence: 99%

Flyback Converter Controller by Arduino Uno

yass¹,

Rashid²

2020

Int. J. Electr. Power Eng.

View full text Add to dashboard Cite

This study presented a flyback converter that regulates output voltage to give a desired value and can used in many application such as power supply. To give a regulated output voltage from flyback converter a feedback loop with Proportional-Integral (PI) controller is used. A simulation of flyback converter is employed by MATLAB/Simulink. Also a practical implementation is used microcontroller Arduino to control on the duty cycle through IC2112 driver at change in the input voltage or resistive load. The duty controller to create regulate output voltage by using voltage mode control.

show abstract

MATLAB-Arduino as a low cost microcontroller for 3 phase inverter

Cited by 17 publications

References 9 publications

Universal power converter for low power applications

Universal power converter for low power applications

Solar Energy Measurement Using Arduino

Flyback Converter Controller by Arduino Uno

Contact Info

Product

Resources

About