New technique for deposition and thermochemical treatment of small parts with complex geometry applied to machining inserts

Lima, Ramsés Otto Cunha; Alves, Clodomiro; Melo, Anderson Clayton Alves de; Alves, Salete Martins; Filho, Lino Araújo

doi:10.1016/j.jmrt.2020.11.047

Cited by 4 publications

(2 citation statements)

References 21 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…При высоких температурах упругие модули зависят от температуры, что подтверждается экспериментально [21][22][23][24][25][26]. Для нашего случая применяем их линейную зависимость:…”

Section: основы математической моделиunclassified

The influence exerted by active cooling on the permanent connection formed as a result of electric arc welding

Ткачева

Abashkin

2022

PNRPU Mechanics Bulletin

View full text Add to dashboard Cite

The problem of temperature stresses is solved in the work. The process of electric arc welding with guaranteed penetration of steel plates of various thicknesses is simulated. The possibility of reducing residual stresses formed as a result of welding by applying heat removal from the surface of the near-weld region of a steel plate is being investigated. The temperature distribution is determined by solving a non-linear heat equation, in which the specific heat and thermal conductivity depend on temperature. The heat source is modeled using the double ellipsoid method proposed by John A. Goldak. The horseshoe-shaped heat sink follows immediately after the anode spot and is set by the heat flux in such a way that the main temperature of the plate does not decrease below its initial temperature. This limitation reduces the level of the temperature gradient, thereby reducing the stresses in the metal plate. To illustrate the effect of active heat sink, the temperature distribution in the top layer at the moment of termination of welding is compared with and without active heat sink. The material is assumed to be elastoviscoplastic, the deformations are small and consist of reversible and irreversible ones. Reversible deformations are related to stresses by the Duhamel - Neumann law. Irreversible strains increase when the von Mises plastic flow condition is satisfied, in which there is a plastic strain rate component responsible for the plastic flow viscosity. The elastic moduli (Young's modulus, Poisson's ratio) and the yield strength are assumed to be temperature dependent. The solution of the mechanical part of the problem is found by the method of simple iterations. For plates with different thicknesses, diagrams of residual stresses are given, located in the center of the plate from the seam to the periphery. As a result of the work, according to the obtained distributions of residual stresses in the plate material, it is concluded that the use of an active horseshoe-shaped heat sink from the near-weld zone when welding thin steel plates reduces residual stresses, therefore it is recommended to use in the welding process. The use of an active heat sink on the reverse side of the plate leads to an increase in the stress level, therefore it is not recommended for use.

show abstract

Section: основы математической моделиunclassified

The influence exerted by active cooling on the permanent connection formed as a result of electric arc welding

Ткачева

Abashkin

2022

PNRPU Mechanics Bulletin

View full text Add to dashboard Cite

show abstract

“…Exhaust gasses from motor vehicles reach highly toxic levels in a short time, causing symptoms such as nausea, dizziness, burning eyes, malaise, and unconsciousness. Gasses released by vehicles during operation are not only harmful to the respiratory system, but also carcinogenic, especially when come from of diesel engines 3,7,9,[25][26][27][28][29][30] .…”

Section: Introductionmentioning

confidence: 99%

Deposition of Ti-Based Thin Films on AISI 1020 Steel Substrates Using the Cathodic Cage Plasma Deposition Technique

Silva,

Cardoso,

Gontijo

et al. 2023

Mat. Res.

View full text Add to dashboard Cite

The automotive industry is one of the largest industrial segments in the world market. The exhaust system of motor vehicles is responsible for the emission and treatment of toxic gasses released by the engine. In this sense, the application of titanium on an AISI 1020 steel substrate was carried out by plasma deposition using a cathode cage. The aim of this research was to evaluate the application of this material in the exhaust system of motor vehicles. The samples were characterized by scanning electron microscopy (SEM), confocal microscopy (CM), microhardness tests and corrosion resistance tests. The samples exhibited a thin film with higher titanium content and hardness than the uncoated sample. The corrosion potential also increased and the current density was lower than the uncoated sample. The conclusion is that the deposition of thin titanium films on AISI 1020 steel with CCPD has the potential to produce thin films.

show abstract

Wear mechanisms of TiN coated tools during high-speed tapping of GGG50 nodular cast iron

Val

Alonso²,

Veiga³

et al. 2023

Wear

View full text Add to dashboard Cite

New technique for deposition and thermochemical treatment of small parts with complex geometry applied to machining inserts

Cited by 4 publications

References 21 publications

The influence exerted by active cooling on the permanent connection formed as a result of electric arc welding

The influence exerted by active cooling on the permanent connection formed as a result of electric arc welding

Deposition of Ti-Based Thin Films on AISI 1020 Steel Substrates Using the Cathodic Cage Plasma Deposition Technique

Wear mechanisms of TiN coated tools during high-speed tapping of GGG50 nodular cast iron

Contact Info

Product

Resources

About