Wear mechanisms of TiN coated tools during high-speed tapping of GGG50 nodular cast iron

Val, Alain Gil Del; Alonso, Unai; Veiga, Fernando; Arizmendi, M.

doi:10.1016/j.wear.2022.204558

Cited by 5 publications

(1 citation statement)

References 19 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…GGG50 material, which is one of the cast irons, has the property of spheroidal graphite with high wear resistance and high tensile strength capacity. Silicon, which is present at the rate of 2-4% in cast iron, causes the carbon to be found in the form of graphite leaflets, which facilitates the machinability of the material [2][3][4][5]. There are quite a variety of methods in the machining industry.…”

Section: Introductionmentioning

confidence: 99%

Investigation of The Chip Formed as a Result of Machining of GGG50 Casting Material by Turning Method

Kaya

Binali

Kuntoğlu

2023

ICRAS

View full text Add to dashboard Cite

– In this study, the relationship between the chips formed during the machining of GGG50 materialby turning method in different parameters was investigated. GGG50 material is spheroidal graphite castiron, which can melt at low temperatures and has high wear resistance. Silicon, which is present at the rateof 2-4% in cast iron, causes the carbon to be found in the form of graphite leaflets, which facilitates themachinability of the material. Chips reflect the machining properties of the material in the manufacturingindustry and are also responsible for removing heat from the cutting zone. It also plays an important role inmeasuring the machining capabilities and strengths of cutting tools. In the experiments, three main factorsaffecting the state of the chips in the turning process were discussed. These are cutting speed, depth of cutand feed rate. As a result of the study, the most important parameter affecting the chips in the turning ofthe GGG50 material in terms of thickness was determined as the cutting speed. The results of theseexperiments are expected to guide future studies in the manufacturing sector.

show abstract

Section: Introductionmentioning

confidence: 99%

Investigation of The Chip Formed as a Result of Machining of GGG50 Casting Material by Turning Method

Kaya

Binali

Kuntoğlu

2023

ICRAS

View full text Add to dashboard Cite

show abstract

Investigation on the tribological properties of different coatings of cutting tool with reciprocating friction test

Li,

Zhang,

Zhao

et al. 2023

J Braz. Soc. Mech. Sci. Eng.

View full text Add to dashboard Cite

Optimization and analysis of machining performance for the milling process during milling of W-Al-Si-C alloy material

Kumar,

Oza,

Bhole

et al. 2023

Innov. Emerg. Technol.

View full text Add to dashboard Cite

This study determined the optimum HSS cutting tool technique parameters for milling W-Al-Si-C rods using Taguchi methodology. This paper explains the empirical results of the selection of appropriate cutting settings that assure lower power consumption in high-end Computer Numerical Control (CNC) machines. An experiment employing the Taguchi methodology on an extruded W-Al- Si-C rod was performed on a CNC lathe with cutting speed, feed rate, and depth of cut as the process parameters. The performance characteristics (energy usage) were quantified by a data collection system. Minor energy process parameters were selected after data analysis. Experimental results are presented to demonstrate the worth of the chosen methodology. A total of 350[Formula: see text]rpm, 0.37[Formula: see text]mm/rev feed rate, and 1[Formula: see text]mm of cut depth produced the best MRR result. The maximum material removal rate (MRR) is obtained at lower levels of spindle speed and depth of cut, i.e., 1.452[Formula: see text]g/sec.

show abstract

Wear mechanisms of TiN coated tools during high-speed tapping of GGG50 nodular cast iron

Cited by 5 publications

References 19 publications

Investigation of The Chip Formed as a Result of Machining of GGG50 Casting Material by Turning Method

Investigation of The Chip Formed as a Result of Machining of GGG50 Casting Material by Turning Method

Investigation on the tribological properties of different coatings of cutting tool with reciprocating friction test

Optimization and analysis of machining performance for the milling process during milling of W-Al-Si-C alloy material

Contact Info

Product

Resources

About