On the mechanical behavior of BFRP to aluminum AA6086 mixed joints

Fiore, Vincenzo; Alagna, F.; Bella, G. Di; Valenza, A.

doi:10.1016/j.compositesb.2012.12.009

Cited by 47 publications

(11 citation statements)

References 30 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The peak load and average data were recorded and calculated. The GRE plate was placed on top, while AA7075 was place at the bottom as reported by [16,[36][37]. higher accuracy three replicates were tested at each stress level.…”

Section: 3experimental Setupmentioning

confidence: 99%

Tensile and fatigue properties of single lap joints of aluminium alloy/glass fibre reinforced composites fabricated with different joining methods

Mariam

Afendi

Majid

et al. 2018

Composite Structures

View full text Add to dashboard Cite

show abstract

Section: 3experimental Setupmentioning

confidence: 99%

Tensile and fatigue properties of single lap joints of aluminium alloy/glass fibre reinforced composites fabricated with different joining methods

Mariam

Afendi

Majid

et al. 2018

Composite Structures

View full text Add to dashboard Cite

show abstract

“…Whatever is the application area, the use of monolithic structures is extremely rare or limited to very specific applications so that there is always the necessity to join composite components to other composites or metallic parts in order to produce the whole structure. Normally, the parts made of composites are realized by hand lay‐up, vacuum bagging or other manufacturing technique and then they are joined with metal ones through a structural adhesive, a mechanical connection or a combination of these last .…”

Section: Introductionmentioning

confidence: 99%

Failure maps to assess bearing performances of glass composite laminates

et al. 2018

View full text Add to dashboard Cite

FIG. 4. Images of (a) shear out fracture on G_4_4_15, (b) net tension fracture on G_8_8_15, and (c) bearing fracture on G_6_15_15. [Color figure can be viewed at wileyonlinelibrary.com] FIG. 5. Bearing stress-displacement curves at varying edge distance for samples with (a) 4 mm and (b) 8mm hole diameter. [Color figure can be viewed at wileyonlinelibrary.com] FIG. 7. (a) Mesh 3D surface plot and (b) failure mechanisms map on mesh 3D surface plot of bearing stress at varying E/D and W/D parameters. [Color figure can be viewed at wileyonlinelibrary.com]

show abstract

“…Di Franco et al [84] demonstrated that by combining SPR and adhesive bonding, joints with a high strength, a high stiffness and high-energy absorption could be achieved. Fiore et al [85] studied the mechanical performance of a Basalt fibre-reinforced polymer to aluminium alloy AA6086 mixed joints. Their results showed that the strength of the self-piercing riveted joints was lower than that of the adhesive-bonded joints.…”

Section: Suitable Materials For Spr Joiningmentioning

confidence: 99%

Self-piercing riveting-a review

Chrysanthou

Imran

et al. 2017

Int J Adv Manuf Technol

239

View full text Add to dashboard Cite

Self-piercing riveting (SPR) is a cold mechanical joining process used to join two or more sheets of materials by driving a rivet piercing through the top sheet or the top and middle sheets and subsequently lock into the bottom sheet under the guidance of a suitable die. SPR is currently the main joining method for aluminium and mixed-material lightweight automotive structures. SPR was originated half century ago, but it only had significant progress in the last 25 years due to the requirement of joining lightweight materials, such as aluminium alloy structures, aluminium-steel structures and other mixed-material structures, from the automotive industry. Compared with other conventional joining methods, SPR has many advantages including no pre-drilled holes required, no fume, no spark and low noise, no surface treatment required, ability to join multi-layer materials and mixed materials and ability to produce joints with high static and fatigue strengths. In this paper, research investigations that have been conducted on self-piercing riveting will be extensively reviewed. The current state and development of SPR process is reviewed and the influence of the key process parameters on joint quality is discussed. The mechanical properties of SPR joints, the corrosion behaviour of SPR joints, the distortion of SPR joints and the simulation of SPR process and joint performance are reviewed. Developing reliable simulation methods for SPR process and joint performance to reduce the need of physical testing has been identified as one of the main challenges.

show abstract

On the mechanical behavior of BFRP to aluminum AA6086 mixed joints

Cited by 47 publications

References 30 publications

Tensile and fatigue properties of single lap joints of aluminium alloy/glass fibre reinforced composites fabricated with different joining methods

Tensile and fatigue properties of single lap joints of aluminium alloy/glass fibre reinforced composites fabricated with different joining methods

Failure maps to assess bearing performances of glass composite laminates

Self-piercing riveting-a review

Contact Info

Product

Resources

About