2016
DOI: 10.1109/jphotov.2016.2600341
|View full text |Cite
|
Sign up to set email alerts
|

Performance Improvement of Perovskite Solar Cells Based on PCBM-Modified ZnO-Nanorod Arrays

Help me understand this report

Search citation statements

Order By: Relevance

Paper Sections

Select...
2
1
1

Citation Types

0
14
0
1

Year Published

2017
2017
2023
2023

Publication Types

Select...
5
1

Relationship

0
6

Authors

Journals

citations
Cited by 23 publications
(15 citation statements)
references
References 52 publications
0
14
0
1
Order By: Relevance
“…The TiO 2 based PSCs often demonstrate significant non-radiative recombination. A thin layer of fullerene derivatives [32c,87a,230] or PCBM [231] and PCBA [232] have shown to increase electron injection into ESC. Wojciechowski et al [32c] demonstrated via PL decay and photothermal deflection spectroscopy that the traps states are significantly passivated when the TiO 2 layer is functionalized with a fullerene derivative SAM.…”
Section: Interfacial Modifiers To Improve Pv Performance Of Perovskitmentioning
confidence: 99%
“…The TiO 2 based PSCs often demonstrate significant non-radiative recombination. A thin layer of fullerene derivatives [32c,87a,230] or PCBM [231] and PCBA [232] have shown to increase electron injection into ESC. Wojciechowski et al [32c] demonstrated via PL decay and photothermal deflection spectroscopy that the traps states are significantly passivated when the TiO 2 layer is functionalized with a fullerene derivative SAM.…”
Section: Interfacial Modifiers To Improve Pv Performance Of Perovskitmentioning
confidence: 99%
“…The higher efficiency for PSCs demonstrated in tandem configurations . Currently, the most commonly used electron transporting materials (ETM) are TiO 2 , ZnO, and PCBM whereas the most efficient p‐type organic contacts are Spiro‐MeOTAD, PEDOT:PSS and also inorganic ones such as CuI, CuSCN, Cu 2 O, and NiO x …”
Section: Introductionmentioning
confidence: 99%
“…The higher efficiency for PSCs demonstrated in tandem configurations. [15,16] Currently, the most commonly used electron transporting materials (ETM) are TiO 2 , [17,18] ZnO, [19,20] and PCBM [21,22] whereas the most efficient p-type organic contacts are Spiro-MeOTAD, [5] PEDOT:PSS [22] and also inorganic ones such as CuI, [23] CuSCN, [24] Cu 2 O, [25] and NiO x . [26][27][28][29][30][31] In the PSCs architecture, using inorganic materials as an ETM and HTM propose higher durability, mechanical stability, and possibility to reach robust and low-cost solar cells rather than organic ones.…”
Section: Introductionmentioning
confidence: 99%
“…[71][72][73] In addition, C60-SAM also passivated trap states in HP (at the interface), consequently reducing the non-radiative recombination, and finally increasing the EL efficiency. 72 Besides, the fullerene and its derivatives, as PCBM, 74 benzoic acid derivatives 75 have been also used to improve the electron extraction efficiency.…”
Section: I22 Brief Introduction On the Interaction Of Perovskite Wmentioning
confidence: 99%
“…25 Figure III.4a shows the normalized photoluminescence (PL) of the single HP and QD layers. In addition, bilayers formed by both combinations of QD/HP and HP/QD were also studied with a type II alignment due to the relative large bandgap of the PbS QDs in 74 comparison with other experiments. Interestingly bilayer samples presents a new feature in the near infrared region (NIR) that it is not observed for single layer samples, HP or QD, as can be observed in Figure III.4b.…”
mentioning
confidence: 99%