Phase and Structural Transformations in Heat Resistant Alloys during Direct Laser Deposition

Buczak, Nadine; Hassel, Thomas; Kislov, Nikita G.; Klimova-Korsmik, Olga; Turichin, Gleb; Magerramova, Lubov A.

doi:10.4028/www.scientific.net/kem.822.389

Cited by 4 publications

(1 citation statement)

References 9 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Additive technologies, most commonly based on the use of virtual models, are widely available due to the fact that they allow the manufacturing of products with complex geometric shapes and profiles. The use of such advanced technologies will significantly reduce the time introduction of products to the market and their cost, reduce material consumption, and reduce the product failure, which is a clear advantage for use in most industries [ 1 , 2 , 3 ].…”

Section: Introductionmentioning

confidence: 99%

Features of Heat Treatment the Ti-6Al-4V GTD Blades Manufactured by DLD Additive Technology

et al. 2021

View full text Add to dashboard Cite

Additive manufacturing of titanium alloys is one of the fastest growing areas of 3D metal printing. The use of AM methods for parts production in the aviation industry is especially promising. During the deposition of products with differently sized cross-sections, the thermal history changes, which leads to non-uniformity of the structure and properties. Such heterogeneity can lead to failure of the product during operation. The structure of deposited parts, depending on the thermal cycle, may consist of α’, α + α’ + β’, and α + β in different ratios. This problem can be solved by using heat treatment (HT). This paper presents research aimed towards the determination of optimal heat treatment parameters that allows the reception of the uniform formation of properties in the after-treatment state, regardless of the initial structure and properties, using the example of a deposited Ti-6Al-4V gas turbine blade.

show abstract

Section: Introductionmentioning

confidence: 99%

Features of Heat Treatment the Ti-6Al-4V GTD Blades Manufactured by DLD Additive Technology

et al. 2021

View full text Add to dashboard Cite

show abstract

Multilayer composite Ti-6Al-4 V/Cp-Ti alloy produced by laser direct energy deposition

Gushchina

Kuzminova

Dubinin

et al. 2022

Int J Adv Manuf Technol

View full text Add to dashboard Cite

Effect of Scanning Strategy on Mechanical Properties of Ti-6Al-4V Alloy Manufactured by Laser Direct Energy Deposition

Gushchina

Kuzminova

Kudryavtsev

et al. 2021

J. of Materi Eng and Perform

View full text Add to dashboard Cite

Direct energy deposition (DED) is an additive manufacturing method that allows repairing the broken parts and building the meter-scale samples. However, the printing of large parts is associated with huge residual stresses and martensite phase formation, which can change the geometry of final samples or initiate the crack. The last factor is especially important for titanium alloys. In this work, we investigated the effect of DED thermal history on the obtained structural and mechanical properties of Ti-6Al-4V using a thermocouple. It was demonstrated that printing with long pauses leads to a¢ phase formation, which embrittles the material. Continuous printing with small pauses between tracks leads to the formation of the dual a+b structure. The effect of the texture on the material properties is also discussed. As a result of the study, the specific DED process parameters allow the same mechanical characteristics for as-built titanium alloy and the alloy after heat treatment.

show abstract

Phase and Structural Transformations in Heat Resistant Alloys during Direct Laser Deposition

Cited by 4 publications

References 9 publications

Features of Heat Treatment the Ti-6Al-4V GTD Blades Manufactured by DLD Additive Technology

Features of Heat Treatment the Ti-6Al-4V GTD Blades Manufactured by DLD Additive Technology

Multilayer composite Ti-6Al-4 V/Cp-Ti alloy produced by laser direct energy deposition

Effect of Scanning Strategy on Mechanical Properties of Ti-6Al-4V Alloy Manufactured by Laser Direct Energy Deposition

Contact Info

Product

Resources

About