Precise Temperature Stabilizing System of Liquids for the purpose Biomedical Applications

Vozda, M.; Sekora, Jiří; Penhaker, Marek

doi:10.5755/j01.eee.18.10.3056

Cited by 3 publications

(2 citation statements)

References 3 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In the case of greenhouse automation, it's used to take temperature, humidity and atmospheric pressure measurements in its immediate vicinity Vozda et al (2012). Another feature of this expansion is the ability to work with real time clock.…”

Section: Meteo Shieldmentioning

confidence: 99%

Design and Realization of Low Cost Control for Greenhouse Environment with Remote Control

Bajer

Krejcar

2015

IFAC-PapersOnLine

View full text Add to dashboard Cite

This project describes the design and implementation of control unit coordinating sensors of various physical quantities and actuators. Beside the data collection from sensor units, the problem consists of their local and remote visualization. The selected concept is created by the Arduino platform, which uses expansion modules for data acquisition and visualization to control the solution. The chosen solution is sufficient for home automation and is useful for a wide range of potential customers. The concept is concretized into an intelligent greenhouse environment, where complete control is designed over the environment. Such solution optimizes the quality of treatment of crops or flowers while it can also bring financial savings on subsequent operation of the system, as expected. Results of the control concept were tested with the good results during a trial run of a real greenhouse, in which the quality of the designed solution was verified. Specific procedures and design solutions are also listed within this paper to highlight the solution.

show abstract

Section: Meteo Shieldmentioning

confidence: 99%

Design and Realization of Low Cost Control for Greenhouse Environment with Remote Control

Bajer

Krejcar

2015

IFAC-PapersOnLine

View full text Add to dashboard Cite

show abstract

“…Lienhard IV and Lienhard V, 2012;Lewis et al, 2004;Vozda et al, 2012). During the sintering process and cooling phase of sintered parts are thermal conduction and thermal convection very important modes for data collection and evaluation of heat effects.…”

mentioning

confidence: 99%

Material and Thermal Analysis of Laser Sinterted Products

Hudák¹,

Šarik²,

Dadej³

et al. 2013

Acta Mechanica Et Automatica

View full text Add to dashboard Cite

Thermal analysis of laser processes can be used to predict thermal stresses and consequently deformation in a completed part. Analysis of temperature is also the basic for feedback of laser processing parameters in manufacturing. The quality of laser sintered parts greatly depends on proper selection of the input processing parameters, material properties and support creation. In order to relatively big heat stress in the built part during sintering process, the thermal simulation and thermal analysis, which could help better understand and solve the issue of parts deformations is very important. Main aim of presented work is to prepare input parameters for thermal simulations by the use of RadTherm software (Thermoanalytics Inc., USA), directly during the sintering process and after the process and find out the impact of the heat stress on a final shape and size of the prototype. Subsequently, an annealing process of constructed products after DMLS could be simulated and specified.

show abstract

3D Bioprinters - Future of Implants Biofabrication

Hudák¹,

Živčák²,

Šarik³

et al. 2013

AMS

View full text Add to dashboard Cite

Today he is an associative professor and head of prosthetics and orthotics study program and head of Biomedical Engineering Division at the Department of Biomedical Engineering and Measurement, Technical University of Košice. His research interests include additive manufacturing in medicine, medical thermography, industrial thermography, human biomechanics and rehabilitation technologies. From 2004 to 2009 he was a technical assistant at the Center of Refractive Surgery in Kosice. Mr. Hudak has more than 120 publications in home and foreign journals. He is co-author of 3 monographies and 7 books.

show abstract

Precise Temperature Stabilizing System of Liquids for the purpose Biomedical Applications

Cited by 3 publications

References 3 publications

Design and Realization of Low Cost Control for Greenhouse Environment with Remote Control

Design and Realization of Low Cost Control for Greenhouse Environment with Remote Control

Material and Thermal Analysis of Laser Sinterted Products

3D Bioprinters - Future of Implants Biofabrication

Contact Info

Product

Resources

About