Preparation and compression performance of porous magnesium alloy composite with ceramic hollow spheres

Chen, J.H.; Liu, P.S.; Song, Shuang

doi:10.1016/j.jallcom.2021.162397

Cited by 10 publications

(2 citation statements)

References 25 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The 12%(HNLA-BPA)/5%(MoO3) hybrid composite was found to be higher hardness than the other composites due to the increasing weight fraction of reinforcement particles; the hardness value increased gradually. The improvement in the hardness of the composite is also due to the formation of homogenous dispersoids [24]. It might re ne the grain size of the matrix, improving the composite's property.…”

Section: Microhardness Testmentioning

confidence: 99%

Tribological and Mechanical Characteristics of Mg–Zn6.0–Y1.2–Zr0.2 alloy by SPS Technique: Natural and Agro-Waste Utilization

Vinod

Suresh²,

Reddy³

et al. 2022

J Bio Tribo Corros

View full text Add to dashboard Cite

In India, urban solid waste generation has risen over the last decade. The aspect of waste generation is a large amount of waste materials among all solid waste types. While using ash particles eliminates waste, it also contributes desirable qualities. In this research work, the effects of Himalayan nettle leaf ash (HNLA) bean pod ash (BPA) with molybdenum trioxide (MoO3) on the ZWK611 (Mg-Zn6.0-Y1.2-Zr0.2) alloy is examined. The as-cast alloy exhibits an α-Mg matrix, and cubic γ-phases are formed in addition to MoO3 particles. In this work, an attempt was made to choose a ZWK611 alloy reinforced with HNLA and BPA by varying weight percentages (X = 4, 8, 12, and 15%) with a constant weight percentage of MoO3 (5%) fabricated using spark plasma sintering (SPS) technique. The mechanical and physical properties were tested for both as-cast alloy and magnesium hybrid composites. Surface morphology and XRD are analysed to identify material behaviour. The addition of 12%(HNLA-BPA)/5%(MoO3) hybrid composite exhibits high strength as compared to the as-cast alloy.

show abstract

Section: Microhardness Testmentioning

confidence: 99%

Tribological and Mechanical Characteristics of Mg–Zn6.0–Y1.2–Zr0.2 alloy by SPS Technique: Natural and Agro-Waste Utilization

Vinod

Suresh²,

Reddy³

et al. 2022

J Bio Tribo Corros

View full text Add to dashboard Cite

show abstract

“…[1][2][3] Bone tissue engineering scaffolds have been developed with rising demands on biomaterials in terms of mechanical properties, bioactivity, and biodegradability. Up to now, a variety of scaffolds biomaterials have been developed, [4][5][6][7] including bioactive ceramics (e.g., MAO, [8] HA, [9][10][11] ), biodegradable polymers (e.g., PLA, [12] BDSPs [13] ), and biodegradable metals (e.g., Mg, [14][15][16] Zn, [17] Ti [18,19] ). It is worth noting that Mg alloys have attracted extensive attention owing to special features in mechanical properties [20,21] and biological functions, [22] such as the close elastic modulus and density with human cortical bone, [23,24] good biodegradability and biocompatibility.…”

Section: Introductionmentioning

confidence: 99%

Effect of Mn Content on the Microstructure, Mechanical, and Corrosion Properties of Porous Mg–1Zn–1Ca Scaffolds

Li,

Qiu,

et al. 2024

Adv Eng Mater

View full text Add to dashboard Cite

Porous Mg alloys scaffolds are considered as an attractive strategy for bone repair due to their good biodegradability, biocompatibility, and suitable mechanical properties. In this study, porous Mg‐1Zn‐1Ca‐xMn (x = 0, 0.2, 0.5, 0.8) scaffolds with cubic pore structure were prepared, and the size of main pore and interconnected pores of the scaffolds were predicted to be 355∽450 μm, and 30∽50 μm, respectively. Among the four scaffolds, Mg‐1Zn‐1Ca‐0.8Mn scaffold possessed good mechanical properties, with a maximum yield strength of 27.1 and an elastic modulus of 0.66 GPa. However, Mg‐1Zn‐1Ca‐0.5Mn scaffold exhibited the optimal corrosion resistance with a corrosion rate 1.02mm/y after 5 days immersion in Hank’s solution. This is mainly attributed to α‐Mn phase is uniformly distributed on the substrate and uniformly degraded.This article is protected by copyright. All rights reserved.

show abstract

Lotus-type porous magnesium production via in situ pyrolysis of viscose rayon fiber in a melting process

et al. 2023

View full text Add to dashboard Cite

Preparation and compression performance of porous magnesium alloy composite with ceramic hollow spheres

Cited by 10 publications

References 25 publications

Tribological and Mechanical Characteristics of Mg–Zn6.0–Y1.2–Zr0.2 alloy by SPS Technique: Natural and Agro-Waste Utilization

Tribological and Mechanical Characteristics of Mg–Zn6.0–Y1.2–Zr0.2 alloy by SPS Technique: Natural and Agro-Waste Utilization

Effect of Mn Content on the Microstructure, Mechanical, and Corrosion Properties of Porous Mg–1Zn–1Ca Scaffolds

Lotus-type porous magnesium production via in situ pyrolysis of viscose rayon fiber in a melting process

Contact Info

Product

Resources

About