Properties and cutting performance of AlTiCrN/TiSiCN bilayer coatings deposited by cathodic-arc ion plating

Imamura, Satoshi; Fukui, Haruyo; Shibata, Akihiko; Omori, Naoya; Setoyama, Makoto

doi:10.1016/j.surfcoat.2007.05.087

Cited by 19 publications

(7 citation statements)

References 9 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Yang et al [7] reported high wear and erosion resistance and good anti-corrosion performance for CrTiAlN coatings. TiCrAlN coatings showed improved cutting performance in the machining of hardened steels [8,9], whereas bilayer AlTiCrN/TiSiCN coatings demonstrated excellent cutting performance on various types of materials (carbon steel, hardened steel, and gray cast iron) [10].…”

Section: Introductionmentioning

confidence: 99%

Comparative investigation of TiAlC(N), TiCrAlC(N), and CrAlC(N) coatings deposited by sputtering of МАХ-phase Ti2−Cr AlC targets

Shtansky

Kiryukhantsev-Korneev

Sheveyko

et al. 2009

Surface and Coatings Technology

View full text Add to dashboard Cite

Section: Introductionmentioning

confidence: 99%

Comparative investigation of TiAlC(N), TiCrAlC(N), and CrAlC(N) coatings deposited by sputtering of МАХ-phase Ti2−Cr AlC targets

Shtansky

Kiryukhantsev-Korneev

Sheveyko

et al. 2009

Surface and Coatings Technology

View full text Add to dashboard Cite

“…In conventional magnetron sputtering, a negative substrate bias voltage is usually applied to improve the structure densification of the deposited coatings, which however inevitably results in high residual compressive stresses in the coatings, e.g. as being measured in this study and shown in literature [24,42,[51][52][53] . Such residual stresses are known to be deteriorating to the adhesion property of hard coatings, especially for those to be used under severe tribological loading conditions.…”

Section: Effect Of Hipims On Coating Structurementioning

confidence: 83%

Hybrid HIPIMS and DC magnetron sputtering deposition of TiN coatings: Deposition rate, structure and tribological properties

Luo

Yang

Cooke

2013

Surface and Coatings Technology

View full text Add to dashboard Cite

Abstract:High power impulse magnetron sputtering (HIPIMS) has the advantage of ultra-dense plasma deposition environment although the resultant deposition rate is significantly low. By using a closed field unbalanced magnetron sputtering system, a hybrid process consisting of one HIPIMS powered magnetron and three DC magnetrons has been introduced in the reactive sputtering deposition of a TiN hard coating on a hardened steel substrate, to investigate the effect of HIPIMS incorporation on the deposition rate and on the microstructure and mechanical and tribological properties of the deposited coating. Various characterizations and tests have been applied in the study, including XRD, FEG-SEM, cross-sectional TEM, Knoop hardness, adhesion tests and unlubricated ball-on-disk tribo-tests. The results revealed that, both the DC magnetron and hybrid-sputtered TiN coatings exhibited dense columnar morphology, a single NaCl-type cubic crystalline phase with strong (220) texture, and good adhesion property. The two coatings showed similar dry sliding friction coefficient of 0.8 -0.9 and comparable wear coefficient in the range of 1 -2 × 10 -15 m 3 N -1 m -1 . The overall deposition rate of the hybrid sputtering, being 0.047 µm/min as measured in this study, was governed predominantly by the three DC magnetrons whereas the HIPIMS only made a marginal contribution. However, the incorporated HIPIMS has been found to lead to remarkable reduction of the compressive residual stress from -6.0 to -3.5 GPa and a slight increase in the coating hardness from 34.8 to 38.0 GPa.

show abstract

“…Going from these relevant aspects from industrial practice, the researches made in different countries such as Japan, China [1,3,4], Ireland [2] emphasized a series of knowledge that refer to technologies and studies with fundamental and experimental character which lead to improving superficial layers properties by using the impulse electric discharges method. It is seen that the main causes that produce the necessity of replacing some system parts in automotive industry are the destructions of surface layer through wear, fatigue and corrosion (ex.…”

Section: Introductionmentioning

confidence: 99%

"Microstructural Analysis of Three Layer Depositions with Ni and Ti on Steel Using the EDS Method"

Perju¹,

Nejneru²,

Tugui³

et al. 2019

MMS

View full text Add to dashboard Cite

The ESD method (electro spark deposition) is used to cover through deposition the active parts of machines, working in heavy abrasive wear moist environment as well as in a dry environment. The paper proposes the use ESD method for Fe-C alloys for obtaining thin layers system with physical-mechanical properties improved comparing to base material. Due to polar effect, the predominant transfer of anode's material (electrode) towards cathode (piece) assures the forming of the superficial layer with well-determined physicalchemical properties. In addition, in multiple layers case the deposit of a supplementary layer emphasizes the diffusion of the first deposited layer by anchoring more the coating.

show abstract

Properties and cutting performance of AlTiCrN/TiSiCN bilayer coatings deposited by cathodic-arc ion plating

Cited by 19 publications

References 9 publications

Comparative investigation of TiAlC(N), TiCrAlC(N), and CrAlC(N) coatings deposited by sputtering of МАХ-phase Ti2−Cr AlC targets

Comparative investigation of TiAlC(N), TiCrAlC(N), and CrAlC(N) coatings deposited by sputtering of МАХ-phase Ti2−Cr AlC targets

Hybrid HIPIMS and DC magnetron sputtering deposition of TiN coatings: Deposition rate, structure and tribological properties

"Microstructural Analysis of Three Layer Depositions with Ni and Ti on Steel Using the EDS Method"

Contact Info

Product

Resources

About