Recycling and utilization assessment of waste fired clay bricks (Grog) with granulated blast-furnace slag for geopolymer production

Zawrah, M.F.; Gado, R.A.; Feltin, Nicolas; Ducourtieux, S.; Devoille, Laurent

doi:10.1016/j.psep.2016.08.001

Cited by 192 publications

(68 citation statements)

References 46 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…It should be noted here that silica comes from two different sources, sodium silicate and the aluminosilicate material used. The results of this study show that the insufficient quantity of Na + ions and the unreacting excess of Si 4+ ions have a negative reflection on the mechanical strength of cured geopolymers [26]. The increase in the Na 2 SiO 3 /NaOH ratio increases the sodium content in the mixture.…”

Section: Silicate/hydroxide Ratiomentioning

confidence: 72%

“…The improvement in compressive strength is mainly due to the inclusion of blast furnace slag in the matrix, which leads to the reinforcement of the geopolymer binder. In addition, the amount of calcium oxide (CaO) contained in the ground granulated blast furnace slag precursor (GGBFS) was found to have a significant impact on the resulting cured geopolymer and therefore shows an improvement in the mechanical properties of the specimens [26]. The optimal resistance is obtained using 8 M NaOH, with a value of 6.21 MPa.…”

Section: Ggbfs/wb Ratiomentioning

confidence: 99%

“…The combination of fly ash and waste bricks was presented by Rovanîk et al [25]. Another study on the recycling of waste bricks and slag into new building material was presented by Zawrah et al [26].…”

mentioning

confidence: 99%

“…GGBFS is a waste produced by the iron blast furnace and subsequently tempered, and it is essentially composed by calcium alumino-silicate which is overload [26]. The GGBFS can be added to the geopolymer formulation since this component was proven to be one of the best activated materials, resulting in an increase in compressive strength and other mechanical properties [27,28].…”

mentioning

confidence: 99%

See 3 more Smart Citations

Reuse of waste bricks: a new generation of geopolymer bricks

et al. 2019

View full text Add to dashboard Cite

In this study, the potential for reuse of waste brick (WB) by alkaline activation in a new geopolymer brick was examined. The effect of the incorporation of ground granulate blast furnace slag (GGBFS), the molarity of sodium hydroxide (NaOH) and the silicate to sodium hydroxide ratio (Na 2 SiO 3 /NaOH) on the mechanical properties of the final product was investigated. The manufacturing of geopolymer bricks was carried out by mixing WBs, GGBFS, sand with a solution of hydroxide and sodium silicate. The samples were prepared according to different formulations. The optimal compressive strength obtained is 89.91 MPa, for a GGBFS/WB ratio of 80/20, an 8 M molarity of NaOH and a silicate/hydroxide ratio of 2/1. This study shows an effective feasibility for the recovery and recycling of industrial waste into a valuable product for the construction sector. This recycling method can bring environmental and economic benefits by using it as an alternative material to fired brick in construction. Given the results obtained, it will be interesting to study the environmental and economic impact as well as the durability properties of these geopolymer bricks. Graphical abstractKeywords Geopolymer · Recovery of waste bricks · GGBFS · Reuse · Alkaline activation · Compressive strength

show abstract

Section: Silicate/hydroxide Ratiomentioning

confidence: 72%

Section: Ggbfs/wb Ratiomentioning

confidence: 99%

mentioning

confidence: 99%

mentioning

confidence: 99%

See 2 more Smart Citations

Reuse of waste bricks: a new generation of geopolymer bricks

et al. 2019

View full text Add to dashboard Cite

show abstract

“…2A). The bands in range 1620 -1750 cm -1 are attributed to H-O-H bending [11]. The asymmetric stretch of Al-O are observed at bands 1042 cm -1 [12].…”

Section: Characteristics Of Adsorbentsmentioning

confidence: 93%

Analysis of Mass Transfer Resistance for Adsorption of Phosphate onto Industrial Waste Materials in Plug-flow column

Khamidun

Rahman

2017

MATEC Web Conf.

View full text Add to dashboard Cite

Abstract. The understanding resistance of mass transfer for adsorption of phosphate (PO 4 3-) onto industrial waste such as clay brick and ceramic as an adsorbent is important to verify. This study presented the removal of PO 4 3-from a synthetic solution by adsorbing onto the clay brick and ceramic wastes in a plug flow column (PFC). The experimental results showed that increasing the flow rate was decreases the breakthrough time. The mass transfer factor (MTF) models were used to study the behaviours of breakthrough curve and to determine the resistance of mass transfer. The MTF models verified that the resistance of mass transfer could be dependent on porous diffusion until the percentage of outflow reaches 72% for clay brick waste and 86% for ceramic waste, even though film mass transfer can play a minor role in controlling the movement of PO 4 3-from the bulk water to film zone. The results of MTF models coefficient could be indicated to increase the capacity of clay brick and ceramic wastes to adsorb PO 4 3-from synthetic solution, it needs to develop the porosity of these adsorbents by either physical or chemical modification.

show abstract

High‐performance engineered geopolymer composites: A sustainable approach using recycled brick waste

Ahmed,

Abdulrahman,

Atmaca

et al. 2024

J of Applied Polymer Sci

View full text Add to dashboard Cite

This study examines the viability of using construction waste, specifically recycled brick waste powder (RBWP), as an alternative conventional industrial byproduct (fly ash) in the manufacturing of engineered geopolymer composites (EGC). The EGC mixtures are made with 40 μm diameter and 12 mm length polyvinyl alcohol (PVA) fiber. RBWP replaces class‐F fly ash in EGC by 0, 20%, 40%, 60%, 80%, and 100%. This study produces six distinct EGC mixtures in total. The flexural strength, abrasion resistance, sorptivity, and water absorption of the EGC are investigated. Microstructural characterization is carried out using scanning electron microscopy (SEM). Based on the results, when fly ash is replaced by 40% and 100%, respectively, adding RBWP to the EGC mixes significantly improves flexural strength by 39% and midspan deflection by 169%. Nevertheless, abrasion resistance significantly improves when fly ash is completely replaced with RBWP, even though sorptivity and water absorption increase by about 128% and 240%, respectively. The volume change is reduced by 25.4% when RBWP is used. Furthermore, the SEM study shows that the RBWP undergoes active geopolymerization in the EGC mixes.

show abstract

Recycling and utilization assessment of waste fired clay bricks (Grog) with granulated blast-furnace slag for geopolymer production

Cited by 192 publications

References 46 publications

Reuse of waste bricks: a new generation of geopolymer bricks

Reuse of waste bricks: a new generation of geopolymer bricks

Analysis of Mass Transfer Resistance for Adsorption of Phosphate onto Industrial Waste Materials in Plug-flow column

High‐performance engineered geopolymer composites: A sustainable approach using recycled brick waste

Contact Info

Product

Resources

About