SCFs in tubular X-joints retrofitted with FRP under out-of-plane bending moment

Nassiraei, Hossein; Rezadoost, Pooya

doi:10.1016/j.marstruc.2021.103010

Cited by 33 publications

(8 citation statements)

References 22 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Some traditional materials have struggled to meet the demands of various industries for their specific strength, stiffness, and other properties as science and technology have advanced. The emergence of composite materials has greatly aided in the development of materials by resolving these issues to a greater extent [1][2][3]. Metal matrix composites have drawn significant attention from various industries, particularly heavy industries, and are increasingly used in many fields such as aerospace, the automobile industry, biomedicine, and electronic packaging.…”

Section: Introductionmentioning

confidence: 99%

Interface stress transfer model and modulus parameter equivalence method for composite materials embedded with tensile pre-strain shape memory alloy fibers

Huang,

Duan,

Wang

et al. 2024

PLoS ONE

View full text Add to dashboard Cite

The constitutive model and modulus parameter equivalence of shape memory alloy composites (SMAC) serve as the foundation for the structural dynamic modeling of composite materials, which has a direct impact on the dynamic characteristics and modeling accuracy of SMAC. This article proposes a homogenization method for SMA composites considering interfacial phases, models the interface stress transfer of three-phase cylinders physically, and derives the axial and shear stresses of SMA fiber phase, interfacial phase, and matrix phase mathematically. The homogenization method and stress expression were then used to determine the macroscopic effective modulus of SMAC as well as the stress characteristics of the fiber phase and interface phase of SMA. The findings demonstrate the significance of volume fraction and tensile pre-strain in stress transfer between the fiber phase and interface phase at high temperatures. The maximum axial stress in the fiber phase is 705.05 MPa when the SMA is fully austenitic and the pre-strain increases to 5%. At 10% volume fraction of SMA, the fiber phase’s maximum axial stress can reach 1000 MPa. Ultimately, an experimental verification of the theoretical calculation method’s accuracy for the effective modulus of SMAC lays the groundwork for the dynamic modeling of SMAC structures.

show abstract

Section: Introductionmentioning

confidence: 99%

Interface stress transfer model and modulus parameter equivalence method for composite materials embedded with tensile pre-strain shape memory alloy fibers

Huang,

Duan,

Wang

et al. 2024

PLoS ONE

View full text Add to dashboard Cite

show abstract

“…They found that the location of the hole and the orientation of the laminate were the main factors affecting the stress concentration around the hole. Nassiraei et al [ 26 ] investigated the effect of material parameters and joint shape on the stress concentration factor (SCF) of a chord member on a tubular X-shaped joint reinforced with fiber-reinforced polymer (FRP) by means of a finite element method. They also studied the initial stiffness, ultimate capacity, capacity ratio, and failure mechanism of tubular X-shaped joints reinforced with FRP under compressive loading [ 27 ].…”

Section: Introductionmentioning

confidence: 99%

Damage Analysis of CFRP Hybrid Bonded-Bolted Joint during Insertion of Interference-Fit Bolt

2023

View full text Add to dashboard Cite

In this study, experiments and finite element analysis (FEA) were used to evaluate the impact of interference-fit sizes on CFRP hybrid bonded-bolted (HBB) joint damage during bolt insertion. The specimens were designed in accordance with the ASTM D5961 standard and bolt insertion tests were performed at selected interference-fit sizes (0.4%, 0.6%, 0.8%, and 1%). Damage to composite laminates was predicted using the Shokrieh–Hashin criterion and Tan’s degradation rule via the user subroutine USDFLD, while damage to the adhesive layer was simulated by the Cohesive Zone Model (CZM). The corresponding bolt insertion tests were performed. The variation of insertion force with interference-fit size was discussed. The results showed that matrix compressive failure was the main failure mode. With the growth of the interference-fit size, more failure modes appeared, and the failure region expanded. Regarding the adhesive layer, it did not completely fail at the four interference-fit sizes. This paper will be helpful in designing composite joint structures and especially for understanding CFRP HBB joint damage and failure mechanisms.

show abstract

“…In the related research on meshing in finite element, Nassiraei [ 15 , 16 ] a used sub-zone method to meshing different regions of FRP retrofitted X-connection, and meshing encryption for the extrapolation region. The simulation results were compared with the experimental data to verify the accuracy of the finite element model.…”

Section: Introductionmentioning

confidence: 99%

Application of Mean Modulus in Three-Point Bending and Roll Forming

et al. 2023

View full text Add to dashboard Cite

Nonlinear unloading plays an important role in predicting springback during plastic forming process. To improve the accuracy of springback prediction which could provide a guide for precision forming, uniaxial tensile tests and uniaxial loading–unloading–loading tensile tests on SUS304 stainless steel were carried out. The flow stress mathematical model and chord modulus mathematical model were calibrated according to the test results. A constant elastic modulus three-point bending finite element model (E0FEMB) and a constant elastic modulus roll forming finite element model (E0FEMR) were established in MSC.MARC. The chord modulus was output by the PLOTV subroutine to determine the mean modulus of different regions, and the mean modulus three-point bending finite element model (E¯cFEMB) and the mean modulus roll forming finite element model (E¯cFEMR) were defined. The constant modulus finite element model (E0FEM) simulation results and the mean modulus finite element model (E¯cFEM) simulation results were compared with the three-point bending tests and roll forming tests test results. The difference between the simulation results and the test results was small, indicating that the mean modulus was feasible to predict the springback, which verified the suitability of the E¯cFEM.

show abstract

SCFs in tubular X-joints retrofitted with FRP under out-of-plane bending moment

Cited by 33 publications

References 22 publications

Interface stress transfer model and modulus parameter equivalence method for composite materials embedded with tensile pre-strain shape memory alloy fibers

Interface stress transfer model and modulus parameter equivalence method for composite materials embedded with tensile pre-strain shape memory alloy fibers

Damage Analysis of CFRP Hybrid Bonded-Bolted Joint during Insertion of Interference-Fit Bolt

Application of Mean Modulus in Three-Point Bending and Roll Forming

Contact Info

Product

Resources

About