The optimal design of lighting systems for designated office building in Thailand according to ministerial, the Type or Size of Building Standards and Rules and Procedures, Building Design for Energy Conservation, Act B.E.2552

Panjavaranont, Surasak; Bhasaputra, Pornrapeepat; Pattaraprakorn, Woraratana; Tirawannavit, Kitti; Kumpeerakupt, Chaiyapat; Rimsmutchai, Somkuan; Pawanawichien, Natapongkorn

doi:10.1109/icuepes.2011.6497773

Cited by 3 publications

(2 citation statements)

References 0 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Based on the simulation result, LED gives the most energy efficient lighting system type for office building. In [8], the study compares the conventional lighting system design of office building versus the Thailand Energy Ministry standard and regulation. Three different sizes of office building were chose to simulate the power of lighting system by various cases, according to illumination standard, and the performance index in term of w/m 2 .…”

Section: Introductionmentioning

confidence: 99%

An analysis of energy saving through delamping method

Halim

Yaakub

Harun

et al. 2019

IJECE

View full text Add to dashboard Cite

Electrical energy consumption is one of the focus areas in Green and Sustainable technology in the 21st century. Many energy consultants offers services to reduce the electricity consumption to the commercial consumer. Many proposals are focusing on selling their energy management system product which cost a lot of initial investment. The problem of applying energy management system is that the building needs major renovation. In this paper, electricity consumption is reduced through delamping method. The delamping is strategizing based on energy efficiency audit. This technique complies with the ASHRAE international standard for office building. The number of light reduced and electricity consumption from this exercise can translate into reduction of maintenance and electricity bill. The comparison of payback period for various energy saving techniques were discussed as well.

show abstract

Section: Introductionmentioning

confidence: 99%

An analysis of energy saving through delamping method

Halim

Yaakub

Harun

et al. 2019

IJECE

View full text Add to dashboard Cite

show abstract

“…One of the most energy consumption area is outdoor and indoor illumination around the entire world. There are many research and development studies in order to decrease consumed energy in this area [1][2][3][4]. By improvements in solid-state lighting (SSL) systems, the development of high power LED is no doubt one of the best inventions at the scientific researches in two decades on lighting systems.…”

Section: Introductionmentioning

confidence: 99%

Thermal analysis and optimization of high power led armature

Şahbaz¹,

Kentli²,

Köten³

2017

THERM SCI

View full text Add to dashboard Cite

It is an effective way of energy conservation to use high power LED armature in street lighting. However, there exists some restrictions in front of the usage of that, like overheating of LED chips and high weight of armature case. Generally, aluminum heat sinks are attached to housing of the armature to get effective working of LED armature. In this study, a street type high power LED armature has been modeled numerically, transient thermal system has been analyzed and the results have been compared with experimental results in order to decrease the armature weigh and increase efficiency. Also, in experimental studies thermal camera and thermocouples have been used for thermal measurements. Finally, multi-objective optimization has been performed to decrease the armature weight, while keeping maximum temperature on armature between in safely working interval.

show abstract

Control model of the roller shutter on cloudy days

Zhang

2017

2017 International Conference on Circuits, Devices and Systems (ICCDS)

View full text Add to dashboard Cite

The optimal design of lighting systems for designated office building in Thailand according to ministerial, the Type or Size of Building Standards and Rules and Procedures, Building Design for Energy Conservation, Act B.E.2552

Cited by 3 publications

References 0 publications

An analysis of energy saving through delamping method

An analysis of energy saving through delamping method

Thermal analysis and optimization of high power led armature

Control model of the roller shutter on cloudy days

Contact Info

Product

Resources

About