Thermodynamic and Kinetics Aspects of High Temperature Oxidation on a 304L Stainless Steel

Lussana, D.; Baldissin, D.; Massazza, M.; Baricco, Marcello

doi:10.1007/s11085-013-9465-0

Cited by 37 publications

(15 citation statements)

References 15 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The presence of a BCC phase after oxidation of austenitic stainless steels has already been reported and its origin has been discussed. It may be attributed to ferrite due to the local composition change of the steel just below the oxide layer [25] or to BCC martensite [26,27].…”

Section: Corrosion Behavior Under Isothermal Oxidationmentioning

confidence: 99%

Comparison of damaging behavior of oxide scales grown on austenitic stainless steels using tensile test and cyclic thermogravimetry

et al. 2016

View full text Add to dashboard Cite

International audienceTwo austenitic stainless steels, AISI 304L and AISI 303, were submitted to cyclic oxidation and to static mechanical loading after isothermal oxidation at 1000 degrees C. Alloy 303 contains ten times more S than 304L and some Mn addition. During the steel process, it formed manganese sulfides that lead to the formation of a less resistant oxide scale. Both alloys showed similar behavior during thermal cycling but breakaway oxidation and intensive spallation occurred much sooner for alloy 303 than for alloy 304L. A correlation could be drawn between tensile test on preoxidized samples, isothermal and cyclic oxidation. (C) 2015 Elsevier Ltd. All rights reserved

show abstract

Section: Corrosion Behavior Under Isothermal Oxidationmentioning

confidence: 99%

Comparison of damaging behavior of oxide scales grown on austenitic stainless steels using tensile test and cyclic thermogravimetry

et al. 2016

View full text Add to dashboard Cite

show abstract

“…Oxide scales thicknesses are about 2.5 ± 0.5 lm and 4 ± 1 lm after oxidation at 900 and 1000°C respectively. A duplex structure is evidenced by EDS mapping and corresponds to the well-described regular situation: a (Mn,Cr) 3 O 4 spinel top layer and Cr 2 O 3 rich inner layer [9,13,14]. At 1000°C, the outer spinel layer is continuous, characterized by large micro-crystallized grains inducing variations in scale thickness.…”

Section: Resultsmentioning

confidence: 83%

Relations Between Oxidation Induced Microstructure and Mechanical Durability of Oxide Scales

et al. 2016

View full text Add to dashboard Cite

OATAO is an open access repository that collects the work of Toulouse researchers and makes it freely available over the web where possible. This is an author-deposited version published in: http://oatao.univ-toulouse.fr/ Eprints ID : 18118 Abstract Most industrial heat-resistant stainless steels contain silicon as a minor constituent. At high temperature, the internal formation of amorphous silica reduces oxidation rates but decreases the metal/oxide interface toughness. Tensile testing experiments performed on AISI 304L previously oxidized in synthetic air for 50 h at 900 or 1000°C showed a relation between the silica morphology and location and the crack patterns. A micromechanical modeling using cohesive zone models to describe interfaces fracture behavior is proposed to investigate relevant parameters controlling the silica/alloy interface debonding. Calculations carried out using the finite elements method have shown that location of silica inclusions and silica/metal interface toughness are key parameters determining the cracks pattern morphology and the critical strain at failure.

show abstract

“…The formation of thick oxide scale could be related to the transition from a protective chromia oxide to poorly protective Fe-rich oxide scale [9,10,13] due to Cr depletion on the steel surface. According to literature [21], at low temperature, the Cr2O3 provides a high protection to oxidation. At high temperatures, the chromia layer starts to transform into a spinel type oxide M3O4 (M = [Cr, Fe]).…”

Section: Resultsmentioning

confidence: 99%

High Temperature Oxidation Behavior of Fe-Cr Steel in Air at 1000-1200 K

et al. 2018

View full text Add to dashboard Cite

Thermodynamic and Kinetics Aspects of High Temperature Oxidation on a 304L Stainless Steel

Cited by 37 publications

References 15 publications

Comparison of damaging behavior of oxide scales grown on austenitic stainless steels using tensile test and cyclic thermogravimetry

Comparison of damaging behavior of oxide scales grown on austenitic stainless steels using tensile test and cyclic thermogravimetry

Relations Between Oxidation Induced Microstructure and Mechanical Durability of Oxide Scales

High Temperature Oxidation Behavior of Fe-Cr Steel in Air at 1000-1200 K

Contact Info

Product

Resources

About