In a local exhaust ventilation system, where the pollutant or the emitted flows are captured near the generated source, the knowledge of the capture efficiency is necessary to evaluate performance. This article reports a study of the influence of the exhaust hood slot height on the capture efficiency. For this study, the emission of gases and vapors from open surface tanks used in industrial treatments has been simulated in an installation fitted with two ventilation systems: lateral exhaust and push-pull. Several configurations were possible by varying the geometrical and operational conditions. Both qualitative and quantitative evaluations have been performed, the former through observations of the flows using smoke and the latter by using sulfur hexafluoride as tracer gas. The results obtained on capture efficiency for both ventilation systems tested with several exhaust slot height and as a function of the operating flows rates, are presented. It was found that varying the exhaust slot height between 15 and 45 cm had no effect on capture efficiency. The results show that there are no significant differences between the exhaust slots heights tested, although, in the case of 60 cm for lateral exhaust ventilation, the efficiency was slightly lower.

A pilot installation was designed that simulates a surface treatment tank fitted with a push-pull ventilation system. The installation contained elements for measuring and controlling the operational variables (flow rate and tank temperature) and smoke generating equipment for injecting smoke through the holes of the push unit and from the tank surface. Visual observation and video recording of the flows involved meant it was possible to follow the qualitative behavior of the push flow rate along the tank surface and to identify any emissions not captured by the exhaust system. It was possible to differentiate the initial semifree push curtain, its impact with the tank surface, the wall jet that moved toward the exhaust, and its entrance into the exhaust. The methodology proposed is complemented by a quantitative technique for measuring the efficiency, using sulfur hexafluoride as tracer, which permits the causes and location of losses in the ventilation system to be determined.

A pilot installation was designed that simulates a surface treatment tank fitted with a push-pull ventilation system. The installation contained elements for measuring and controlling the operational variables (flow rate and tank temperature) and smoke generating equipment for injecting smoke through the holes of the push unit and from the tank surface. Visual observation and video recording of the flows involved meant it was possible to follow the qualitative behavior of the push flow rate along the tank surface and to identify any emissions not captured by the exhaust system. It was possible to differentiate the initial semifree push curtain, its impact with the tank surface, the wall jet that moved toward the exhaust, and its entrance into the exhaust. The methodology proposed is complemented by a quantitative technique for measuring the efficiency, using sulfur hexafluoride as tracer, which permits the causes and location of losses in the ventilation system to be determined.

Methodologies are proposed for determining capture efficiencies in the ventilation systems of surface treatment tanks, using test-scale equipment. The equipment, which incorporates a lateral and push-pull ventilation system, can measure and control the variables of interest because it incorporates a tracer gas generator (sulfur hexafluoride, the concentration of which is measured by infrared spectrometer). The experimental methodologies described determine total efficiency (when the tracer is emitted uniformly from the whole surface of the tank) and the so-called transversal linear efficiency (when the tracer is emitted linearly through a perforated tube situated over the tank, parallel to the exhaust hood face). The analytical and graphical relationships that can be are established between the two efficiencies make it possible to detect where the emissions not captured by the ventilation system are produced (i.e., losses to the outside). At the same time, such losses can be quantified. Several experiments, results of which are analyzed by the methods described, are included.

Methodologies are proposed for determining capture efficiencies in the ventilation systems of surface treatment tanks, using test-scale equipment. The equipment, which incorporates a lateral and push-pull ventilation system, can measure and control the variables of interest because it incorporates a tracer gas generator (sulfur hexafluoride, the concentration of which is measured by infrared spectrometer). The experimental methodologies described determine total efficiency (when the tracer is emitted uniformly from the whole surface of the tank) and the so-called transversal linear efficiency (when the tracer is emitted linearly through a perforated tube situated over the tank, parallel to the exhaust hood face). The analytical and graphical relationships that can be are established between the two efficiencies make it possible to detect where the emissions not captured by the ventilation system are produced (i.e., losses to the outside). At the same time, such losses can be quantified. Several experiments, results of which are analyzed by the methods described, are included.