Minimizing Pt loading is essential for designing cost-effective water electrolyzers and fuel cell systems. Recently, three-dimensional macroporous open-pore electroactive supports have been widely regarded as promising architectures to lower loading amounts of Pt because of its large surface area, easy electrolyte access to Pt sites, and superior gas diffusion properties to accelerate diffusion of H2 bubbles from the Pt surface. However, studies to date have mainly focused on Pt loading on Ni-based 3D open pore supports which are prone to corrosion in highly acidic and alkaline conditions. Here, we investigate electrodeposition of Pt nanoparticles in low-loading amounts on commercially available, inexpensive, 3D carbon foam (CF) support and benchmark their activity and stability for electrolytic hydrogen production. We first elucidate the effect of deposition potential on the Pt nanoparticle size, density and subsequently its coverage on 3D CF. Analysis of the Pt deposit using scanning electron microscopy images reveal that for a given deposition charge density, the particle density increases (with cubic power) and particle size decreases (linearly) with deposition overpotential. A deposition potential of −0.4 V vs. standard calomel electrode (SCE) provided the highest Pt nanoparticle coverage on 3D CF surface. Different loading amounts of Pt (0.0075–0.1 mgPt/cm2) was then deposited on CF at −0.4 V vs. SCE and subsequently studied for its hydrogen evolution reaction (HER) activity in acidic 1M H2SO4 electrolyte. The Pt/CF catalyst with loading amounts as low as 0.06 mgPt/cm2 (10-fold lower than state-of-the-art commercial electrodes) demonstrated a mass activity of 2.6 ampere per milligram Pt at 200 mV overpotential, nearly 6-fold greater than the commercial Pt/C catalyst tested under similar conditions. The 3D architectured electrode also demonstrated excellent stability, showing <7% loss in activity after 60 h of constant current water electrolysis at 100 mA/cm2.
Tin‐based chalcogenide semiconductors, though attractive materials for photovoltaics, have to date exhibited poor performance and stability for photoelectrochemical applications. Here, a novel strategy is reported to improve performance and stability of tin monosulfide (SnS) nanoplatelet thin films for H2 production in acidic media without any use of sacrificial reagent. P‐type SnS nanoplatelet films are coated with the n‐CdS buffer layer and the TiO2 passivation layer to form type II heterojunction photocathodes. These photocathodes with subsequent deposition of Pt nanoparticles generate a photovoltage of 300 mV and a photocurrent density of 2.4 mA cm−2 at 0 V versus reversible hydrogen electrode (RHE) for water splitting under simulated visible‐light illumination (λ > 500 nm, P in = 80 mW cm−2). The incident photon‐to‐current efficiency at 0 V versus RHE for H2 production reach a maximum of 12.7% at 575 nm with internal quantum efficiency of 13.8%. The faradaic efficiency for hydrogen evolution remains close to unity after 6000 s of illumination, confirming the robustness of the heterojunction for solar H2 production.
Photoelectrooxidation of chloride ions to chlorine with co-production of hydrogen by water reduction has been proposed as a means of decreasing the net solar hydrogen production cost. So far, however, most such solar-to-chlorine production systems use cost-prohibitive materials and/or show rather small faradaic yield or stability. Here we report the development of earth-abundant, nanostructured bismuth vanadate/tungsten oxide (BiVO 4 /WO 3 ) photoanode assemblies that operate in acidic sodium chloride solution (pH 1; 4 M) to produce chlorine while generating hydrogen at the dark cathode. We show that electrodeposition of 20 nm WO 3 coating protects BiVO 4 from harsh pH and oxidative environments while being catalytically active for chlorine evolution. The heterostructured BiVO 4 /WO 3 photoanodes yield average photocurrent densities of 2.5 ± 0.3 mA cm −2 at 1.42 V RHE (Reversible Hydrogen Electrode) under 1 sun illumination. After two hours of continuous illumination, the best performing devices demonstrate faradaic efficiencies of 85% for chlorine production and 100% for hydrogen production.
Surface wettability plays an important role in heterogeneous electrocatalysis. Here we report a facile laser ablation strategy to directly modify the wettability of the silver catalyst surface and investigate its...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2025 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.