No abstract

Objectives: Cone beam computed tomography (CBCT) imaging is becoming an indispensable intraoperative tool; however, the current field of view prevents visualization of long anatomical sites, limiting clinical utility. Here, we demonstrate the longitudinal extension of the intraoperative CBCT field of view using a multi-turn reverse helical scan and assess potential clinical utility in interventional procedures. Materials and Methods: A fixed-room robotic CBCT imaging system, with additional real-time control, was used to implement a multi-turn reverse helical scan. The scan consists of C-arm rotation, through a series of clockwise and anticlockwise rotations, combined with simultaneous programmed table translation. The motion properties and geometric accuracy of the multi-turn reverse helical imaging trajectory were examined using a simple geometric phantom. To assess potential clinical utility, a pedicle screw posterior fixation procedure in the thoracic spine from T1 to T12 was performed on an ovine cadaver. The multi-turn reverse helical scan was used to provide postoperative assessment of the screw insertion via cortical breach grading and mean screw angle error measurements (axial and sagittal) from 2 observers. For all screw angle measurements, the intraclass correlation coefficient was calculated to determine observer reliability. Results: The multi-turn reverse helical scans took 100 seconds to complete and increased the longitudinal coverage by 370% from 17 cm to 80 cm. Geometric accuracy was examined by comparing the measured to actual dimensions (0.2 ± 0.1 mm) and angles (0.2 ± 0.1 degrees) of a simple geometric phantom, indicating that the multi-turn reverse helical scan provided submillimeter and degree accuracy with no distortion. During the pedicle screw procedure in an ovine cadaver, the multi-turn reverse helical scan identified 4 cortical breaches, confirmed via the postoperative CT scan. Directly comparing the screw insertion angles (n = 22) measured in the postoperative multi-turn reverse helical and CT scans revealed an average difference of 3.3 ± 2.6 degrees in axial angle and 1.9 ± 1.5 degrees in the sagittal angle from 2 expert observers. The intraclass correlation coefficient was above 0.900 for all measurements (axial and sagittal) across all scan types (conventional CT, multi-turn reverse helical, and conventional CBCT), indicating excellent reliability between observers.Conclusions: Extended longitudinal field-of-view intraoperative 3-dimensional imaging with a multi-turn reverse helical scan is feasible on a clinical robotic CBCT imaging system, enabling long anatomical sites to be visualized in a single image, including in the presence of metal hardware.

BackgroundIatrogenic injury to the femoral neurovascular bundle is not uncommon during primary and revision total hip replacement (THR) and can result in permanent weakness, pain and poor function. Prevention of injury to these structures relies on a sound knowledge of their relationships to the hip joint.MethodsWe studied 115 consecutive hip magnetic resonance imaging (MRI) results in order to identify objective relationships between these structures and the hip joint that can be used intraoperatively.ResultsWe determined that the shortest mean distances of the femoral nerve, artery and vein from the hip joint are 23.62 (standard deviation, SD = 5.44), 19.62 (SD = 4.17) and 17.47 (SD = 4.41) mm, respectively. The femoral nerve was lateral to the hip joint in 30 (55.5%) left- and 37 (60.7%) right-sided hip joints. The femoral artery was located medial to the hip joint in 28 (51.9%) left- and 34 (55.7%) right-sided hips. The femoral vein was medial to the hip joint in 52 (96.3%) left- and 58 (95.1%) right-sided hips.ConclusionWe have identified objective relationships between the hip joint and femoral neurovascular bundle that can be used with ease intraoperatively during THR. Our data show that patients with a low body weight and the elderly may be at a higher risk of iatrogenic injury due to increased proximity of the neurovascular structures to the hip. Application of this knowledge may serve to reduce the risk of iatrogenic injury to these structures and thereby improve patient satisfaction and outcomes.

Background The emergence of robotic Cone Beam Computed Tomography (CBCT) imaging systems in trauma departments has enabled 3D anatomical assessment of musculoskeletal injuries, supplementing conventional 2D fluoroscopic imaging for examination, diagnosis, and treatment planning. To date, the primary focus has been on trauma sites in the extremities. Purpose To determine if CBCT images can be used during the treatment planning process in spinal instrumentation and laminectomy procedures, allowing accurate 3D‐printed pedicle screw and laminectomy drill guides to be generated for the cervical and thoracic spine. Methods The accuracy of drill guides generated from CBCT images was assessed using animal cadavers (ovine and porcine). Preoperative scans were acquired using a robotic CBCT C‐arm system, the Siemens ARTIS pheno (Siemens Healthcare, GmbH, Germany). The CBCT images were imported into 3D‐Slicer version 4.10.2 (http://www.slicer.org) where vertebral models and specific guides were developed and subsequently 3D‐printed. In the ovine cadaver, 11 pedicle screw guides from the T1–T5 and T7–T12 vertebra and six laminectomy guides from the C2–C7 vertebra were planned and printed. In the porcine cadaver, nine pedicle screw guides from the C3–T4 vertebra were planned and printed. For the pedicle screw guides, accuracy was assessed by three observers according to pedicle breach via the Gertzbein–Robbins grading system as well as measured mean axial and sagittal screw error via postoperative CBCT and CT scans. For the laminectomies, the guides were designed to leave 1 mm of lamina. The average thickness of the lamina at the mid‐point was used to assess the accuracy of the guides, measured via postoperative CBCT and CT scans from three observers. For all measurements, the intraclass correlation coefficient (ICC) was calculated to determine observer reliability. Results Compared with the planned screw angles for both the ovine and porcine procedures (n = 32), the mean axial and sagittal screw error measured on the postoperative CBCT scans from three observers were 3.9 ± 1.9° and 1.8 ± 0.8°, respectively. The ICC among the observes was 0.855 and 0.849 for the axial and sagittal measurements, respectively, indicating good reliability. In the ovine cadaver, directly comparing the measured axial and sagittal screw angle of the visible screws (n = 14) in the postoperative CBCT and conventional CT scans from three observers revealed an average difference 1.9 ± 1.0° in axial angle and 1.8 ± 1.0° in the sagittal angle. The average thickness of the lamina at the middle of each vertebra, as measured on‐screen in the postoperative CBCT scans by three observes was 1.6 ± 0.2 mm. The ICC among observers was 0.693, indicating moderate reliability. No lamina breaches were observed in the postoperative images. Conclusion Here, CBCT images have been used to generate accurate 3D‐printed pedicle screw and laminectomy drill guides for use in the cervical and thoracic spine. The results demonstrate sufficient precision compared with th...