Accurate conversion of wideband multi-GHz analog signals into the digital domain has long been a target of analog-to-digital converter (ADC) developers, driven by applications in radar systems, software radio, medical imaging, and communication systems. Aperture jitter has been a major bottleneck on the way towards higher speeds and better accuracy. Photonic ADCs, which perform sampling using ultra-stable optical pulse trains generated by mode-locked lasers, have been investigated for many years as a promising approach to overcome the jitter problem and bring ADC performance to new levels. This work demonstrates that the photonic approach can deliver on its promise by digitizing a 41 GHz signal with 7.0 effective bits using a photonic ADC built from discrete components. This accuracy corresponds to a timing jitter of 15 fs -a 4-5 times improvement over the performance of the best electronic ADCs which exist today. On the way towards an integrated photonic ADC, a silicon photonic chip with core photonic components was fabricated and used to digitize a 10 GHz signal with 3.5 effective bits. In these experiments, two wavelength channels were implemented, providing the overall sampling rate of 2.1 GSa/s. To show that photonic ADCs with larger channel counts are possible, a dual 20-channel silicon filter bank has been demonstrated. 289-296 (1992). 11. J. Kim, J. Chen, J. Cox, and F. X. Kärtner, "Attosecond-resolution timing jitter characterization of free-running mode-locked lasers using balanced optical cross-correlation," Opt. Lett. microwave signals at 40-GHz with higher than 7-ENOB resolution," Opt. ©2012 Optical Society of America

For the first time to the authors' knowledge, optical waveguides have been inscribed in bulk crystalline silicon by ultrafast laser radiation. Femtosecond laser pulses of 40-nm spectral bandwidth, 1-kHz repetition rate, and 1.7-microJ on-target energy were applied at a mid-infrared wavelength of 2.4 microm to induce nonlinear absorption in the focal volume of the beam. By scanning the laser beam with respect to the sample, buried optical waveguides have been created that were single mode at 1550 and 1320 nm and guided light only with its polarization perpendicular to the sample's surface. Propagation losses with an upper limit of 1.2 dB/cm or less were observed throughout the optical telecommunications band.

For the first time to our knowledge, ultrafast laser writing has generated room-temperature stable guided-wave optics in bulk lithium niobate for the telecommunication spectrum. Among a seven-dimensional parameter space for waveguide optimization, two frequently overlooked parameters, pulse duration and polarization, were found to be key in overcoming undesired nonlinear optical responses imposed by this material. Single-mode waveguides were best formed with circularly polarized light having a relatively long pulse duration of approximately 1.0 ps. The waveguides were highly polarization dependent and guided in both telecommunication bands near 1300 and 1550 nm, exhibiting losses as low as 0.7 dB/cm.

For the first time to our knowledge, bulk modification of lithium niobate using high repetition rate ultrashort laser pulses has been studied. A fiber based ultrafast laser has been applied in a range of 0.1 to 1.5 MHz repetition rate to directly inscribe optical waveguides in z-cut lithium niobate. Circularly polarized light with stretched 600 fs pulses produced waveguides with nearly circular mode profiles that guided in the telecom band of 1300 nm. Higher laser repetition rate of 700 kHz was found to offer smooth waveguides with low propagation loss of 0.6 dB/cm, matching the best reported value so far, with the advantage of 50 fold faster writing speed. At repetition rates of 250 kHz and higher, the tracks exhibited a cladding-like modification zone that extended outside the main laser interaction volume, yielding smoother structures, despite higher net fluence delivery, providing concrete evidence of heat accumulation and thermal annealing effects. We also present the first observation of periodic micro-structures in the bulk laser interaction volume of a non-glass material.

We characterize the timing jitter of passively mode-locked, femtosecond, erbium fiber lasers with unprecedented resolution, enabling the observation of quantum-origin timing jitter up to the Nyquist frequency. For a pair of nearly identical 79.4MHz dispersion-managed lasers with an output pulse energy of 450pJ, the high-frequency jitter was found to be 2.6fs [10kHz, 39.7MHz]. The results agree well with theoretical noise models over more than three decades, extending to the Nyquist frequency. It is also found that unexpected noise may occur if care is not taken in optimizing the mode-locked state.