In this paper, polymer composites based on polylactide (PLA) and epoxy resin (Epidian 5) were studied in terms of the influence of magnetic induction on their changes in physicochemical properties. The composites contained admixtures in the form of magnetite (Fe3O4) and crystalline cellulose (Avicel PH-1010) in the amount of 10%, 20%, and 30% by weight and starch in the amount of 10%. The admixtures of cellulose and starch were intended to result in the composites becoming biodegradable biopolymers to some extent. Changes in physical and chemical properties due to the impact of a constant magnetic field with a magnetic induction value B = 0.5 T were observed. The changes were observed during tests of tensile strength, bending, impact strength, water absorbency, frost resistance, chemical resistance to acids and bases, as well as through SEM microscopy and with studies of the composition of the composites that use the EDS method and of their structure with the XRD method. Based on the obtained results, it was found that the magnetic induction value changes the properties of composites. This therefore acts as one method of receiving new alternative materials, the degradation of which in the environment would take far less time.

No abstract

The influence of batched water exposed to a constant magnetic field (B = 1 T) on the properties of concrete was investigated. Fillers such as coal fly ash (CFA), phosphogypsum (PB) and native potato starch dispersed in epoxy resin [EP(S)], were used to obtain concrete based on Portland cement (PC). The magnetized batched water had a positive effect on the properties of concrete, reducing water absorption and increasing flexural and compressive strengths. The obtained concrete is a new promising building material that can be used to manufacture e.g. building foundations, flush-mounted installations and insulation layers.

The aim of the research presented in the paper was to obtain new polymer composites with strong functional properties on the Epidian 5 epoxy resin matrix. The polymer composites contained admixtures of expanded graphite, powder graphite, birch bark containing botulin, and yellow dextrin in set amounts of 20% by weight. Their various mechanical parameters and physicochemical properties were investigated. The research involved determining the effect of a constant magnetic field with magnetic induction B, under the influence of which the parameters and properties of polymer composites have been changed. For example, in a constant magnetic field with an induction of B = 0.5 T there was an increase in the hardness of the composite with an admixture of birch bark from 24.01 to 26.96 N/mm2 (12.3%), or in the composite with the addition of yellow dextrin from 26.12 to 29.93 N/mm2 (14.6%). It was also found, for example, that the water absorption of the resin itself decreased from 0.18% to 0.13%, and the composite with graphite powder from 0.48% to 0.46%. Changes in these parameters, often beneficial, may be important in terms of potential application of those new materials in industry as alternatives.

In this paper, the separation technology of components of waste pharmaceutical blisters and its adaptation to the industrial scale are described. It involved, among others, taking advantage of the phenomenon of difference in the density of the individual phases that were contained in the separation tank, i.e., the separating mixture, PVC plastics, and aluminium. As a result, the directions of movement of the separated blister components were opposite. All components of the separating mixture feature a similar surface tension (γ > 20 mN/m) which facilitates the penetration of the liquid between the blister component layers. After separation, the full-value products, i.e. polyvinyl chloride (PVC) and aluminium are obtained. The resulting products can be further processed and the entire technological process is a waste-free. PVC can be melted and processed into other products e.g. plastic components for the construction industry. Pure aluminium is a metal sought after and widely used in industry due to its low specific weight. An additional element supplementing the technology is the separation tank of our design in which the separation process of the blister components takes place. The advantage of the separation tank is that the separation process can be repeated many times with the same separating mixture until it is exhausted. Both separated blister components are directed to filtering followed by air drying without a mixing PVC plastic with aluminium.