Osteoarthritis (OA) is a chronic, progressive disease which has over 300 million cases each year. Some of the main symptoms of OA are pain, restriction of joint motion and stiffness of the joint. Early diagnosis and treatment can prolong painless joint function. Vibroarthrography (VAG) is a cheap, reproducible, non-invasive and easy-to-use tool which can be implemented in the diagnostic route. The aim of this study was to establish diagnostic accuracy and to identify the most accurate signal processing method for the detection of OA in knee joints. In this study, we have enrolled a total of 67 patients, 34 in a study group and 33 in a control group. All patients in the study group were referred for surgical treatment due to intraarticular lesions, and the control group consisted of healthy individuals without knee symptoms. Cartilage status was assessed during surgery according to the International Cartilage Repair Society (ICRS) and vibroarthrography was performed one day prior to surgery in the study group. Vibroarthrography was performed in an open and closed kinematic chain for the involved knees in the study and control group. Signals were acquired by two sensors placed on the medial and lateral joint line. Using the neighbourhood component analysis (NCA) algorithm, the selection of optimal signal measures was performed. Classification using artificial neural networks was performed for three variants: I—open kinetic chain, II—closed kinetic chain, and III—open and closed kinetic chain. Vibroarthrography showed high diagnostic accuracy in determining healthy cartilage from cartilage lesions, and the number of repetitions during examination can be reduced only to closed kinematic chain.

The recommendations put forward in the International Standards for anchorage in concrete concerning the assessment of the load-carrying capacity of anchors (the pull-out force) embedded in natural rock material were verified. Regarding the predicted extent of surface failure we have shown, in earlier studies, substantial discrepancies between the strength test results for anchorages in the rock mass and the established standard recommendations for anchorages in concrete. As regards the industrial practice and the goals of the reported project, simplified calculation procedures that will facilitate the selection of optimal configurations for the layout of anchor holes, while being computationally effective and applicable under the industry-specific conditions are sought.

This paper is a discussion of the results of tests intended to (i) estimate the effects of component mix ratios and heat curing of an adhesive joint on the tensile strength, and (ii) to determine the adhesive component mix ratio for which heat curing is insignificant to the strength of adhesive butt joints. Experimental tests were carried out at ambient temperature and elevated temperature during which adhesive butt joints were loaded with a tensile force until failure. The variables were the mix ratio of epoxy adhesive components and the application of heat holding at the adhesive curing stage. An LSTM (long short-time memory) forecast was used to determine the point corresponding to the mix ratio of adhesive components at which heat holding of the adhesive joint no longer has a positive and significant importance to the final tensile strength of the joint.

Cartilage loss due to osteoarthritis (OA) in the patellofemoral joint provokes pain, stiffness, and restriction of joint motion, which strongly reduces quality of life. Early diagnosis is essential for prolonging painless joint function. Vibroarthrography (VAG) has been proposed in the literature as a safe, noninvasive, and reproducible tool for cartilage evaluation. Until now, however, there have been no strict protocols for VAG acquisition especially in regard to differences between the patellofemoral and tibiofemoral joints. The purpose of this study was to evaluate the proposed examination and acquisition protocol for the patellofemoral joint, as well as to determine the optimal examination protocol to obtain the best diagnostic results. Thirty-four patients scheduled for knee surgery due to cartilage lesions were enrolled in the study and compared with 33 healthy individuals in the control group. VAG acquisition was performed prior to surgery, and cartilage status was evaluated during the surgery as a reference point. Both closed (CKC) and open (OKC) kinetic chains were assessed during VAG. The selection of the optimal signal measures was performed using a neighborhood component analysis (NCA) algorithm. The classification was performed using multilayer perceptron (MLP) and radial basis function (RBF) neural networks. The classification using artificial neural networks was performed for three variants: I. open kinetic chain, II. closed kinetic chain, and III. open and closed kinetic chain. The highest diagnostic accuracy was obtained for variants I and II for the RBF 9-35-2 and MLP 10-16-2 networks, respectively, achieving a classification accuracy of 98.53, a sensitivity of 0.958, and a specificity of 1. For variant III, a diagnostic accuracy of 97.79 was obtained with a sensitivity and specificity of 0.978 for MLP 8-3-2. This indicates a possible simplification of the examination protocol to single kinetic chain analyses.

The purpose of the study was to test the usefulness of deep learning artificial neural networks and statistical modeling in predicting the strength of bone cements with defects. The defects are related to the introduction of admixtures, such as blood or saline, as contaminants into the cement at the preparation stage. Due to the wide range of applications of deep learning, among others in speech recognition, bioinformation processing, and medication design, the extent was checked to which it is possible to obtain information related to the prediction of the compressive strength of bone cements. Development and improvement of deep learning network (DLN) algorithms and statistical modeling in the analysis of changes in the mechanical parameters of the tested materials will enable determining an acceptable margin of error during surgery or cement preparation in relation to the expected strength of the material used to fill bone cavities. The use of the abovementioned computer methods may, therefore, play a significant role in the initial qualitative assessment of the effects of procedures and, thus, mitigation of errors resulting in failure to maintain the required mechanical parameters and patient dissatisfaction.