In this paper the three-dimensional inverse design code TURBOdesign-1 is applied to the design of the blade geometry of a centrifugal compressor impeller with splitter blades. In the design of conventional impellers the splitter blades normally have the same geometry as the full blades and are placed at mid-pitch location between the two full blades, which can usually result in a mismatch between the flow angle and blade angles at the splitter leading edge. In the inverse design method the splitter and full blade geometry is computed independently for a specified distribution of blade loading on the splitter and full blades. In this paper the basic design methodology is outlined and then the flow in the conventional and inverse designed impeller is compared in detail by using computational fluid dynamics (CFD) code TASCflow. The CFD results confirm that the inverse design impeller has a more uniform exit flow, better control of tip leakage flow and higher efficiency than the conventional impeller. The results also show that the shape of the trailing edge geometry has a very appreciable effect on the impeller Euler head and this must be accurately modeled in all CFD computations to ensure closer match between CFD and experimental results. Detailed measurements are presented in part II of the paper.

Background: The blade sections of industrial axial flow compressors require a wider range from surge to choke than typical gas turbine compressors in order to meet the high volume flow range requirements of the plant in which they operate. While in the past conventional blade profiles (NACA65 or C4 profiles) at moderate Mach number have mostly been used, recent well-documented experience in axial compressor design for gas turbines suggests that peak efficiency improvements and considerable enlargement of volume flow range can be achieved by the use of so-called prescribed velocity distribution (PVD) or controlled diffusion (CD) airfoils. Method of approach: The method combines a parametric geometry definition method, a powerful blade-to-blade flow solver and an optimization technique (breeder genetic algorithm) with an appropriate fitness function. Particular effort has been devoted to the design of the fitness function for this application which includes non-dimensional terms related to the required performance at design and off-design operating points. It has been found that essential aspects of the design (such as the required flow turning, or mechanical constraints) should not be part of the fitness function, but need to be treated as so-called “killer” criteria in the genetic algorithm. Finally, it has been found worthwhile to examine the effect of the weighting factors of the fitness function to identify how these affect the performance of the sections. Results: The system has been tested on the design of a repeating stage for the middle stages of an industrial axial compressor. The resulting profiles show an increased operating range compared to an earlier design using NACA65 profiles. Conclusions: A design system for the blade sections of industrial axial compressors has been developed. Three-dimensional CFD simulations and experimental measurements demonstrate the effectiveness of the new profiles with respect to the operating range.

Industrial centrifugal compressors have a very large field of applications in chemical, petrochemical and gas transport applications with an enormous variety of gases, pressure levels and suction volumes. This paper describes the special design features of this type of compressor and sheds light on a method of standardization to overcome the large diversity of machine types. It reviews the aerodynamic and thermodynamic aspects in the design of impellers and diffusers, discusses the importance of the stage matching and illuminates the effect of stage components on stability.

The focus of this paper lies on the leakage flow across the shroud of a centrifugal compressor impeller. It is common practice to use shrouded impellers in multi stage compressors featuring a single shaft. The rotating impeller then has to be sealed against the higher pressure in the downstream diffuser by means of labyrinths. The relative amount of leakage is higher for stages designed for low flow, meaning that the associated losses gain in relevance. In addition to this loss source, the injection of the leakage flow has a serious influence on the main flow in a region where it is prone to separation, i.e. at the suction side of the impeller blades close to the shroud, where the highest relative velocities are found. The present paper discusses the numerical results of several geometrical arrangements where the leakage flow was mixed with the main flow in different ways. The distance between the location of injection and the leading edge of the impeller as well as the orientation of the injected flow showed a distinct influence on the performance of the entire stage, mainly on stability.

This paper presents an experimental investigation of two centrifugal compressor stage configurations. The baseline configuration has been designed using conventional design engineering tools. The second configuration was designed using advanced inverse design rules as described in Part I. It is designed to match the choke flow as well as the best point of the conventionally designed stage. The experimental investigation is conducted in the industry-scale centrifugal compressor facility at the Turbomachinery Laboratory of the Swiss Federal Institute of Technology. Performance maps for both configurations at several speed lines are presented. These plots show the overall behavior of the stages designed using the different design approaches and their operating range. Time-resolved measurements show details of the unsteady flow field within the diffuser close to the impeller exit. The time-resolved data have been analyzed to assist the explanation of changes in the characteristics and associated efficiency penalties and gains. The processed data show the benefits of the new inverse design method with respect to an improvement of the compressor efficiency and the operating range. It is seen that the application of an inverse design method results in a more uniform flow into the diffuser.