ObjectiveTo identify the effects of a custom-made rigid foot orthosis (RFO) in children over six years old with pes planus.MethodsThe medical records of 39 children (mean age, 10.3±4.09 years) diagnosed with pes planus, fitted with RFOs, and had who more than two consecutive radiological studies were reviewed. The resting calcaneal stance position (RCSP), anteroposterior talocalcaneal angle (APTCA), lateral talocalcaneal angle (LTTCA), the lateral talometatarsal angle (LTTMA), and calcaneal pitch (CP) of both feet were measured to evaluate foot alignment. After diagnosis, children were fitted with a pair of RFOs and recommended to walk with heel strike and reciprocal arm swing to normalize the gait pattern. A follow-up clinical evaluation with radiological measurements was performed after 12-18 months and after 24 months of RFO application. Post-hoc analysis was used to test for significant differences between the radiological indicators and RCSP.ResultsWith RFOs, all radiological indicators changed in the corrective direction except LTTCA. RCSP and CP in the third measurement showed significant improvement in comparison with the second and baseline measurements. Additionally, APTCA and LTTMA revealed improvements at the third measurement versus the baseline measurements.ConclusionThis study revealed that radiological indicators improved significantly after 24 months of RFO application. A prospective long-term controlled study with radiographical evaluation is necessary to confirm the therapeutic effects of RFOs and to determine the optimal duration of wear in children with pes planus.

No abstract

Although orthotic modification using the inverted technique is available for the treatment of flatfoot, empirical evidence for the biomechanical effects of inverted-angle foot orthoses (FOs) is lacking. The aim of this study was to evaluate the effects of different FO inversion angles on plantar pressure during gait in children with flatfoot. Twenty-one children with flexible flatfeet (mean age 9.9 years) were enrolled in this study. The plantar pressures were measured for the rearfoot; medial and lateral midfoot; and medial, central, and lateral forefoot as participants walked on a treadmill while wearing shoes only and shoes with the following 3 orthotic conditions: (i) orthosis with no inverted angle, (ii) orthosis with a 15° inverted angle, and (iii) orthosis with a 30° inverted angle. A one-way repeated measures analysis of variance (ANOVA) with the Bonferroni-adjusted post-hoc test was used to compare the mean values of each orthotic condition. Compared with the shoe only condition, the peak pressure decreased significantly under the medial forefoot and rearfoot with all FOs (p <0.05). However, no significant differences in the peak pressure under the medial forefoot and rearfoot were observed between the FOs. The peak pressure under the medial midfoot increased significantly with all FOs, and a maximal increase in the peak pressure was obtained with a 30° inverted angle orthosis. Furthermore, the contact area under the medial midfoot and rearfoot increased significantly with all FOs, compared with the shoe only condition (p <0.05). Again, no significant differences were observed between the FOs. For plantar pressure redistribution, a FO with a low inverted angle could be effective, accommodative, and convenient for children with flatfoot.

No abstract

The loss of an upper limb significantly limits the functional activities of daily living. A huge emphasis is placed on the manipulation, shape, weight, and comfort of a prosthesis, to enable its use as an inherent body part. Even with technological advances, customized upper-extremity myoelectric prosthesis remain heavy and expensive. The high cost of upper-extremity prosthesis is an especially steep economic barrier for patients. Three-dimensional (3D) printing is a promising avenue for reducing the cost of prosthesis. We applied 3D-printed pressure-sensored prosthetics to a traumatic transradial amputee, and compared the hand functions with a customized myoelectric prosthesis. The 3D-printed pressure-sensored prosthetics showed low grip strength and decreased dexterity compared to the conventional myoelectric prosthesis. Although there were a few limitations, the fabrication of prosthesis with 3D printing technology can overcome previous problems such as high production cost, long fabrication period and heavy weight.