No abstract

An important application of clay is as a solid adsorbent for industrial dyes. The aim of the present work was to carry out an experimental—theoretical study of the adsorption of dye mixtures, namely malachite green (MG) and Congo red (CR), by bentonite. Adsorption studies were conducted after evaluation of the impact of several parameters, including pH, adsorbate dose, and contact time, on the removal of MG and CR. The pH of the dye solution is strongly affected by the chemistry of both the dye molecules and of the adsorbent in an aqueous solution. Where both dye molecules exist in solution, the optimum pH was found to be 8.2 in order to achieve the maximum adsorption of both MG and CR. Preliminary studies showed that 60 min of contact time is sufficient to reach adsorption equilibrium. The adsorption studies were carried out using 1.0 g samples of bentonite. The amount of dye adsorbed was found by application of classical least squares to the synthetic dye mixtures. Data from equilibrium adsorption on bentonite were analyzed by Freundlich, Langmuir, Redlich-Peterson, and Temkin isotherm equations using regression analysis for non-linear forms of those equations. For binary-mixture analysis, isotherm parameters were determined from single-component adsorption studies and the theoretical amount of dye adsorbed was calculated using an extended Langmuir isotherm. Non-linear error analysis showed that the Temkin and Redlich-Peterson isotherms gave the best fits to the equilibrium data for adsorptive removal of MG and CR by bentonite.

In this study, an enzymatic procedure for the determination of glycine (Gly) was developed by using a column containing immobilized glutamate dehydrogenase (GDH) on glyoxal agarose beads. Ammonia is produced from the enzymatic reactions between Gly and GDH with NAD(+) in phosphate buffer medium. The indophenol blue method was used for ammonia detection based on the spectrophotometric measurements of blue-colored product absorbing at 640 nm. The calibration graph is linear in the range of 0.1-10 mM of Gly concentrations. The effect of pH, temperature, and time interval was studied to find column stability, and also the interference effects of other amino acids was investigated. The interaction between GDH and glyoxal agarose beads was analyzed by Fourier transform infrared (FTIR) spectroscopy. The morphology of the immobilized and non-immobilized agarose beads were characterized by atomic force microscopy (AFM).

Dyes are common pollutants in a large variety of industrial wastewaters, and the treatment of these wastes has been extensively studied by coagulation. For the removal of pollutants from the wastewaters, different techniques have been used and electrocougulation is one of the widely used methods. This process is very effective in removing organic pollutants including dyestuff wastewater. The purposes of this study were to investigate the effects of the operating parameters, such as current density, electrolyte concentration, dyestuff concentration, and pH of solution on decolorization and chemical oxygen demand (COD) removal of wastewater containing two different dyes in same solution by direct current electrocoagulation. The amount of dye removed was found by application of first derivative spectrophotometric method to the synthetic dye mixtures. In this work synthetic dye mixture which include C.I. Reactive Yellow 145 (RY145) and C.I. Acid Violet 90 (AV 90) were used for electrocougulation (EC) process with iron electrodes. In the presence of both dye molecules, the optimum pH was found to be 4, optimum NaCI concentration was 3000 mg/L and optimum current density was 5.56 mA/cm2. Under these conditions in the case of 100 mg/L-1 each dye concentration at 20 degrees C and 3 cm interelectro distance the color removal efficiency was reached 97.7% for AV 90 and 97.1% for RY145 in 10 minutes time duration. Dye concentration dependent highest COD removal efficiency was measured as 82% around at 100 mg/L dye concentration.

No abstract