The widespread adaptation of 3D printing in the microfluidic, bioelectronic, and Bio-MEMS communities has been stifled by the lack of investigation into the biocompatibility of commercially available printer resins. By introducing an in-depth post-printing treatment of these resins, their biocompatibility can be dramatically improved up to that of a standard cell culture vessel (99.99%). Additionally, encapsulating resins that are less biocompatible with materials that are common constituents in biosensors further enhances the biocompatibility of the material. This investigation provides a clear pathway toward developing fully functional and biocompatible 3D printed biosensor devices, especially for interfacing with electrogenic cells, utilizing benchtop-based microfabrication, and post-processing techniques.

The development of microelectrode arrays (MEAs) along with complementary advances in electronics, mechanics and software to connect with these arrays has led to the in vitro interfacing and benchtop electrophysiological models of several electrically active cells such as neurons and cardiomyocytes proving vital models and testing of human disease conditions in a dish/on a chip. This topical review deals with the micro/nanofabrication technology development of Microelectrodes Arrays from early silicon based developments to today’s additive manufacturing technologies that have been employed to address bio-micro-electro-mechanical systems tool development in this space. Specifically 2D and 3D MEAs technologies have been reviewed in this paper along with a broad overview of some of the biological applications using these devices that are advancing the very state of biomedical research.

We present a nontraditional fabrication technique for the realization of three-dimensional (3D) microelectrode arrays (MEAs) capable of interfacing with 3D cellular networks in vitro. The technology uses cost-effective makerspace microfabrication techniques to fabricate the 3D MEAs with 3D printed base structures with the metallization of the microtowers and conductive traces being performed by stencil mask evaporation techniques. A biocompatible lamination layer insulates the traces for realization of 3D microtower MEAs (250 μm base diameter, 400 μm height). The process has additionally been extended to realize smaller electrodes (30 μm × 30 μm) at a height of 400 μm atop the 3D microtower using laser micromachining of an additional silicon dioxide (SiO2) insulation layer. A 3D microengineered, nerve-on-a-chip in vitro model for recording and stimulating electrical activity of dorsal root ganglion (DRG) cells has further been integrated with the 3D MEA. We have characterized the 3D electrodes for electrical, chemical, electrochemical, biological, and chip hydration stability performance metrics. A decrease in impedance from 1.8 kΩ to 670 Ω for the microtower electrodes and 55 to 39 kΩ for the 30 μm × 30 μm microelectrodes can be observed for an electrophysiologically relevant frequency of 1 kHz upon platinum electroless plating. Biocompatibility assays on the components of the system resulted in a large range (∼3%–70% live cells), depending on the components. Fourier-transform infrared (FTIR) spectra of the resin material start to reveal possible compositional clues for the resin, and the hydration stability is demonstrated in in-vitro-like conditions for 30 days. The fabricated 3D MEAs are rapidly produced with minimal usage of a cleanroom and are fully functional for electrical interrogation of the 3D organ-on-a-chip models for high-throughput of pharmaceutical screening and toxicity testing of compounds in vitro.

We explore the capabilities and limitations of 3D printed microserpentines (µserpentines) and utilize these structures to develop dynamic 3D microelectrodes for potential applications in in vitro, wearable, and implantable microelectrode arrays (MEAs). The device incorporates optimized 3D printed µserpentine designs with out-of-plane microelectrode structures, integrated on to a flexible Kapton® package with micromolded PDMS insulation. The flexibility of the optimized, printed µserpentine design was calculated through effective stiffness and effective strain equations, so as to allow for analysis of various designs for enhanced flexibility. The optimized, down selected µserpentine design was further sputter coated with 7-70 nm-thick gold and the performance of these coatings was studied for maintenance of conductivity during uniaxial strain application. Bending/conforming analysis of the final devices (3D MEAs with a Kapton® package and PDMS insulation) were performed to qualitatively assess the robustness of the finished device toward dynamic MEA applications. 3D microelectrode impedance measurements varied from 4.2 to 5.2 kΩ during the bending process demonstrating a small change and an example application with artificial agarose skin composite model to assess feasibility for basic transdermal electrical recording was further demonstrated.

We have developed a new technology for the realization of composite biosensor systems, capable of measuring electrical and electrophysiological signals from electrogenic cells, using SeedEZ™ 3D cell culture-scaffold material. This represents a paradigm-shift for BioMEMS processing; 'Biology-Microfabrication' versus the standard 'Microfabrication-Biology' approach. An Interdigitated Electrode (IDE) developed on the 3D cell-scaffold was used to successfully monitor acute cardiomyocyte growth and controlled population decline. We have further characterized processability of the 3D scaffold, demonstrated long-term biocompatibility of the scaffold with various cell lines and developed a multifunctional layered biosensor composites (MLBCs) using SeedEZ™ and other biocompatible substrates for future multilayer sensor integration.