Single-molecule localization microscopy (SMLM) in a typical wide-field setup has been widely used for investigating sub-cellular structures with super resolution. However, field-dependent aberrations restrict the field of view (FOV) to only few tens of micrometers. Here, we present a deep learning method for precise localization of spatially variant point emitters (FD-DeepLoc) over a large FOV covering the full chip of a modern sCMOS camera. Using a graphic processing unit (GPU) based vectorial PSF fitter, we can fast and accurately model the spatially variant point spread function (PSF) of a high numerical aperture (NA) objective in the entire FOV. Combined with deformable mirror based optimal PSF engineering, we demonstrate high-accuracy 3D SMLM over a volume of ~180 × 180 × 5 μm 3 , allowing us to image mitochondria and nuclear pore complex in the entire cells in a single imaging cycle without hardware scanning -a 100-fold increase in throughput compared to the state-of-the-art.

No abstract

Despite the best treatment, approximately 10% of fractures still face undesirable repair and result in delayed unions or non‐unions. Dynamic mechanical stimulation promotes bone formation, when applied at the correct time frame, with optimal loading magnitude, frequency, and repetition. Controlled mechanical loading significantly increases osteogenic cells during the matrix deposition phase of bone repair. In the bone defect, the blood vessel network guides the initial bone formation activities. A unique blood vessel subtype (Type H) exists in bone, which expresses high levels of CD31 and endomucin, and functions to couple angiogenesis and osteogenesis. However, how this form of controlled mechanical loading regulates the Type H vessels and promotes bone formation is still not clear. Sphingosine 1‐phosphate (S1P) participates in the bone anabolic process and is a key regulator of the blood vessel. Its receptor, sphingosine 1‐phosphate receptor 1 (S1Pr1), is a mechanosensitive protein that regulates vascular integrity. Therefore, we hypothesis that controlled anabolic mechanical loading promotes bone repair by acting on Type H vessels. To study the effect of S1Pr1 on loading induced‐bone repair, we utilized a stabilized tibial defect model, which allows for the application of anabolic mechanical loading. Mechanical loading upregulated S1Pr1 within the entire defect, with up to 80% expressed in blood vessels, as observed by deep tissue imaging. Additionally, S1Pr1 antagonism by W146 inhibited the anabolic effects of mechanical loading. We showed that mechanical loading or activating S1Pr1 could induce YAP nuclear translocation, a key regulator in the cell's mechanical response, in endothelial cells (ECs) in vitro. Inhibition of S1Pr1 in endothelial cells by siRNA reduced loading‐induced YAP nuclear translocation and expressions of angiogenic genes. In vivo, YAP nuclear translocation in Type H vessels was up‐regulated after mechanical loading but was inhibited by antagonizing S1Pr1. S1Pr1 agonist, FTY720, increased bone volume and Type H vessel volume, similar to that of mechanical stimulation. In conclusion, controlled anabolic mechanical loading enhanced bone formation mainly through Type H vessels in a S1Pr1‐dependent manner.

No abstract

The advent of precision manufacturing has enabled the creation of pores in metallic scaffolds with feature size in the range of single microns. In orthopedic implants, pore geometries at the micron scale could regulate bone formation by stimulating osteogenic differentiation and the coupling of osteogenesis and angiogenesis. However, the biological response to pore geometry at the cellular level is not clear. As cells are sensitive to curvature of the pore boundary, this study aimed to investigate osteogenesis in high-vs low-curvature environments by utilizing computer numerical control laser cutting to generate triangular and circular precision manufactured micropores (PMpores). We fabricated PMpores on 100 μm-thick stainless-steel discs. Triangular PMpores had a 30°vertex angle and a 300 μm base, and circular PMpores had a 300 μm diameter. We found triangular PMpores significantly enhanced the elastic modulus, proliferation, migration, and osteogenic differentiation of MC3T3-E1 preosteoblasts through Yes-associated protein (YAP) nuclear translocation. Inhibition of Rho-associated kinase (ROCK) and Myosin II abolished YAP translocation in all pore types and controls. Inhibition of YAP transcriptional activity reduced the proliferation, pore closure, collagen secretion, alkaline phosphatase (ALP), and Alizarin Red staining in MC3T3-E1 cultures. In C166 vascular endothelial cells, PMpores increased the VEGFA mRNA expression even without an angiogenic differentiation medium and induced tubule formation and maintenance. In terms of osteogenesis−angiogenesis coupling, a conditioned medium from MC3T3-E1 cells in PMpores promoted the expression of angiogenic genes in C166 cells. A coculture with MC3T3-E1 induced tubule formation and maintenance in C166 cells and tubule alignment along the edges of pores. Together, curvature cues in micropores are important stimuli to regulate osteogenic differentiation and osteogenesis−angiogenesis coupling. This study uncovered key mechanotransduction signaling components activated by curvature differences in a metallic scaffold and contributed to the understanding of the interaction between orthopedic implants and cells.