We describe the design, fabrication, and operation of two types of flow cytometers based on microfluidic devices made of a single cast of poly(dimethylsiloxane). The stream of particles or cells injected into the devices is hydrodynamically focused in both transverse and lateral directions, has a uniform velocity, and has adjustable diameter and shape. The cytometry system built around the first microfluidic device has fluorescence detection accuracy comparable with that of a commercial flow cytometer and can analyze as many as 17 000 particles/s. This high-throughput microfluidic device could be used in inexpensive stand-alone cytometers or as a part of integrated microanalysis systems. In the second device, a stream of particles is focused to a flow layer of a submicrometer thickness that allows imaging the particles with a high numerical aperture microscope objective. To take long-exposure, low-light fluorescence images of live cells, the device is placed on a moving stage, which accurately balances the translational motion of particles in the flow. The achieved resolution is comparable to that of still micrographs. This high-resolution device could be used for analysis of morphology and fluorescence distribution in cells in continuous flow.

Articles you may be interested inTwo-and three-dimensional modeling and optimization applied to the design of a fast hydrodynamic focusing microfluidic mixer for protein folding Phys. Fluids 25, 032001 (2013);

We compared the neutralization sensitivity of early/transmitted HIV-1 variants from patients infected by subtype B viruses at 3 periods of the epidemic (1987–1991, 1996–2000, 2006–2010). Infectious pseudotyped viruses expressing envelope glycoproteins representative of the viral quasi-species infecting each patient were tested for sensitivity to neutralization by pools of sera from HIV-1 chronically infected patients and by an updated panel of 13 human monoclonal neutralizing antibodies (HuMoNAbs). A progressive significantly enhanced resistance to neutralization was observed over calendar time, by both human sera and most of the HuMoNAbs tested (b12, VRC01, VRC03, NIH45-46G54W, PG9, PG16, PGT121, PGT128, PGT145). Despite this evolution, a combination of two HuMoNAbs (NIH45-46G54W and PGT128) still would efficiently neutralize the most contemporary transmitted variants. In addition, we observed a significant reduction of the heterologous neutralizing activity of sera from individuals infected most recently (2003–2007) compared to patients infected earlier (1987–1991), suggesting that the increasing resistance of the HIV species to neutralization over time coincided with a decreased immunogenicity. These data provide evidence for an ongoing adaptation of the HIV-1 species to the humoral immunity of the human population, which may add an additional obstacle to the design of an efficient HIV-1 vaccine.

Studies of the kinetics of biochemical reactions, especially of folding of proteins and RNA, are important for understanding the function of biomolecules and processes in live cells. Many biochemical reactions occur rapidly and thus need to be triggered on very short time scales for their kinetics to be studied, which is often accomplished by mixing in a turbulent flow. More rapid and sample-efficient mixing is achieved in laminar flow in a microfluidic device, in which the sample is two-dimensionally (2D) focused to a thin sheet. Here we describe the design and operation of an ultrafast microfluidic mixer with three-dimensional (3D) flow focusing. The confinement of a 3D-focused sample to a narrow stream near the middle of a microchannel renders its velocity nearly uniform and makes it possible to monitor the reaction kinetics without exclusion of any parts of the sample. Hence, the sample consumption is substantially reduced and the fluorescence of the sample can be monitored without a confocal setup. Moreover, the 3D-focusing allows facile measurements of velocity of the sample with a high spatial resolution using a specially developed technique based on epi-fluorescence imaging. The data on the velocity vs. position are used to precisely calibrate the conversion between position and the reaction time, which is essential for accurate kinetic measurements. The device performs mixing on a 10 ms scale, which is comparable to that of the laminar mixers with 2D focusing. Unlike previous ultrafast laminar mixers, which were machined in hard materials, the present microfluidic device is made of a single cast of poly(dimethylsiloxane), PDMS, and is thus simpler and less expensive to manufacture.