The use of rhBMP-2/absorbable collagen sponge (ACS) combined with all of the bone substitute materials tested resulted in a greater amount of bone formation than that produced with the bone substitute materials alone or rhBMP-2/(ACS) and CL using the rabbit calvarium GBR model.

Several techniques have been proposed for vertical bone regeneration, and many of them use bone autogenous and allogeneic grafts. The purpose of this study was to compare demineralised freeze-dried bone allografts (DFDBA), fresh-frozen (FF) allografts, autogenous bone grafts to find differences between volumetric and histological quantity of bone formation and vertical bone growth dynamic. A vertical tissue regeneration bone model was performed in rabbit calvarias under general anaesthesia. Four hollow cylinders of pure titanium were screwed onto external cortical bone calvarias in eight rabbits. Each one of the cylinders was randomly filled with one intervention: DFDBA, FF, autogenous bone, or left to be filled with blood clot (BC) as control. Allogeneic grafts were obtained from a ninth animal following international standardised protocols for the harvesting, processing, and cryopreservation of allografts. Autogenous graft was obtained from the host femur scraping before adapting hollow cylinders. Animals were euthanized at 13 weeks. Vertical volume was calculated after probe device measurements of the new formed tissue inside the cylinders and after titanium cylinders were removed. Histomorphometry and fluorochrome staining were used to analyse quantity and dynamic of bone formation, respectively. Results showed that DFDBA and fresh-frozen bone improved the velocity and the quantity of bone deposition in distant portions of the basal plane of grafting. Remaining material in allograft groups was more intense than in autogenous group. Both allografts can be indicated as reliable alternatives for volume gain and vertical bone augmentation.

Background: Recombinant human bone morphogenetic protein 2 (rhBMP-2) is an osteoinductor frequently used for bone regeneration in oral and maxillofacial surgery. There is no consensus about the ideal carrier for this growth factor. The aim of this study was to compare the bone augmentation, bone microarchitecture, and biodegradation rate of additional carriers to rhBMP-2/absorbable collagen sponge (ACS) in a vertical guided bone regeneration model. Methods: Four titanium cylinders were fixed onto the calvaria of rabbits (n = 20) that received (n = 10) or not (n = 10) rhBMP-2/ACS in conjunction with one of the carriers: beta-tricalcium phosphate (-TCP), biphasic calcium phosphate (BCP), bovine bone mineral (BBM) or blood clot. The samples were analyzed by means of microcomputed tomography and histomorphology after 14 weeks. Results: All the materials with rhBMP-2/ACS exhibited improvement on bone augmentation, mainly BCP (P = 0.033) and-TCP (P = 0.038), in the upper portion of the cylinder. Although trabecular anisotropy was improved in all the materials groups, trabecular connectivity was diminished when the biomaterials received rhBMP-2/ACS. Resorption rate of the remaining biomaterial was improved by rhBMP-2/ACS, mainly in BBM (P <0.01) and-TCP (P <0.01). BBM exhibited the highest osteoclast density compared with the other materials groups. Conclusions: BCP and-TCP biomaterials exhibited a synergic effect with rhBMP-2/ACS, acting as suitable and viable carriers for vertical bone augmentation. The addition of rhBMP-2 significantly affected the biodegradation of-TCP and BBM, accelerating the resorption of these materials.

The aim of this study was to evaluate the stress distribution of different retention systems (screwed, cemented, and mixed) in 5-unit implant-supported fixed partial dentures through the photoelasticity method. Twenty standardized titanium suprastructures were manufactured, of which 5 were screw retained, 5 were cement retained, and 10 were mixed (with an alternating sequence of abutments), each supported by 5 external hexagon (4.0 mm × 11.5 mm) implants. A circular polariscope was used, and an axial compressive load of 100 N was applied on a universal testing machine. The results were photographed and qualitatively analyzed. We observed the formation of isochromatic fringes as a result of the stresses generated around the implant after installation of the different suprastructures and after the application of a compressive axial load of 100 N. We conclude that a lack of passive adaptation was observed in all suprastructures with the formation of low-magnitude stress in some implants. When cemented and mixed suprastructures were subjected to a compressive load, they displayed lower levels of stress distribution and lower intensity fringes compared to the screwed prosthesis.

No abstract