The dynamics of the three-phase contact line for water and ethanol is experimentally investigated using substrates of various hydrophobicities. Different evolutions of the droplet profile (contact line, R, and contact angle, θ) are found to be dependent on the hydrophobicity of the substrate. A simple theoretical approach based on the unbalanced Young force is used to explain the depinning of the contact line on hydrophilic surfaces or the monotonic slip on hydrophobic substrates. The second part of the article involves the addition of different quantities of titanium oxide nanoparticles to water, and a comparison of the evaporative behavior of these novel fluids with the base liquid (water) on substrates varying in hydrophobicity (i.e., silicon, Cytop, and PTFE) is presented. The observed stick-slip behavior is found to be dependent on the nanoparticle concentration. The evaporation rate is closely related to the dynamics of the contact line. These findings may have an important impact when considering the evaporation of droplets on different substrates and/or those containing nanoparticles.

Superhydrophobicity has received significant attention over the past three decades owing to its significant potential in self-cleaning and anti-icing surfaces, drag reduction, energy harvesting devices, anti-bacterial coatings, and enhanced heat transfer applications. Superhydrophobicity can be obtained via the roughening of an intrinsically hydrophobic surface, the creation of a re-entrant geometry, or by the roughening of a hydrophilic surface followed by a conformal coating of a hydrophobic material. Intrinsically hydrophobic surfaces have poor thermophysical properties such as thermal conductivity, and thus are not suitable for heat transfer applications. Re-entrant geometries, although versatile in applications where droplets are deposited, break down during spatially random nucleation and flood the surface. Chemical functionalization of rough metallic substrates, although promising, is not utilized due to the poor durability of conformal hydrophobic coatings. Here we develop a radically different approach to achieve stable superhydrophobicity. By utilizing laser processing and thermal oxidation of copper (Cu) to create a high surface energy hierarchical copper oxide (CuO), followed by repeatable and passive atmospheric adsorption of hydrophobic volatile organic compounds (VOCs), we show that stable superhydrophobicity with apparent advancing contact angles ≈ 160° and contact angle hysteresis as low as ≈ 20° can be achieved. We exploit the structure length scale and structure geometry dependent VOC adsorption dynamics to rationally design CuO nanowires with enhanced superhydrophobicity. To gain an understanding of the VOC adsorption physics, we utilized X-Ray Photoelectron and Ion Mass Spectroscopy to identify the chemical species deposited on our surfaces in two distinct locations: Urbana, IL, USA and Beijing, China. To test the stability of the atmosphere-mediated superhydrophobic surfaces during heterogeneous nucleation, we used high-speed optical microscopy to demonstrate the occurrence of dropwise condensation and stable coalescenceinduced droplet jumping. Our work not only provides rational design guidelines for developing passively-durable superhydrophobic surfaces with excellent flooding-resistance and self-healing capability, but also sheds light on the key role played by the atmosphere in governing wetting.

Superhydrophobic surfaces are receiving increasing attention due to the enhanced condensation heat transfer, self-cleaning, and anti-icing properties by easing droplet self-removal. Despite the extensive research carried out on this topic, the presence or absence of microstructures on droplet adhesion during condensation has not been fully addressed yet. In this work we, therefore, study the condensation behavior on engineered superhydrophobic copper oxide surfaces with different structural finishes. More specifically, we investigate the coalescence-induced droplet-jumping performance on superhydrophobic surfaces with structures varying from the micro- to the nanoscale. The different structural roughness is possible due to the specific etching parameters adopted during the facile low-cost dual-scale fabrication process. A custom-built optical microscopy setup inside a temperature and relative humidity controlled environmental chamber was used for the experimental observations. By varying the structural roughness, from the micro- to the nanoscale, important differences on the number of droplets involved in the jumps, on the frequency of the jumps, and on the size distribution of the jumping droplets were found. In the absence of microstructures, we report an enhancement of the droplet-jumping performance of small droplets with sizes in the same order of magnitude as the microstructures. Microstructures induce further droplet adhesion, act as a structural barrier for the coalescence between droplets growing on the same microstructure, and cause the droplet angular deviation from the main surface normal. As a consequence, upon coalescence, there is a decrease in the net momentum in the out-of-plane direction, and the jump does not ensue. We demonstrate that the absence of microstructures has therefore a positive impact on the coalescence-induced droplet-jumping of micrometer droplets for antifogging, anti-icing, and condensation heat transfer applications.

Understanding the fundamental mechanisms governing vapor condensation on nonwetting surfaces is crucial to a wide range of energy and water applications. In this paper, we reconcile classical droplet growth modeling barriers by utilizing two-dimensional axisymmetric numerical simulations to study individual droplet heat transfer on nonwetting surfaces (90° < θa < 170°). Incorporation of an appropriate convective boundary condition at the liquid-vapor interface reveals that the majority of heat transfer occurs at the three phase contact line, where the local heat flux can be up to 4 orders of magnitude higher than at the droplet top. Droplet distribution theory is incorporated to show that previous modeling approaches underpredict the overall heat transfer by as much as 300% for dropwise and jumping-droplet condensation. To verify our simulation results, we study condensed water droplet growth using optical and environmental scanning electron microscopy on biphilic samples consisting of hydrophobic and nanostructured superhydrophobic regions, showing excellent agreement with the simulations for both constant base area and constant contact angle growth regimes. Our results demonstrate the importance of resolving local heat transfer effects for the fundamental understanding and high fidelity modeling of phase change heat transfer on nonwetting surfaces.