Introduction
Cervical disc arthroplasty (CDA), a motion-preserving alternative to anterior cervical discectomy and fusion (ACDF), is used in military patients for the treatment of disorders such as spondylosis. Since 2007, the FDA has approved eight artificial discs. The objective of this study is to compare the biomechanics after ACDF and CDA with two FDA-approved devices of differing designs under head and head supported mass loadings.
Materials and Methods
A previously validated osteoligamentous C2-T1 finite element model was used to simulate ACDF and two types of CDA (Bryan and Prodisc C) at the C5-C6 level. The hybrid loading protocol associated with in vivo head and head supported mass was used to apply flexion and extension loading. First, intact spine was subjected to 2 Nm of flexion extension and the range of motion (ROM) was measured. Next, for each surgical option, flexion-extension moments duplicating the same ROM as the intact spine were determined. Under these surgery-specific moments, ROM and facet force were obtained at the index level, and ROM, facet force, and intradiscal pressure at the rostral and caudal adjacent levels.
Results
ACDF led to increased motion, force and pressures at the adjacent levels. Prodisc C led to increased motion and facet force at the index level, and decreased motion, facet force, and intradiscal pressure at both adjacent levels. Bryan produced less dramatic biomechanical alterations compared with ACDF and Prodisc C. Numerical results are given in the article.
Conclusions
Recognizing that ROM is a clinical measure of spine stability/performance, CDA demonstrates a more physiological biomechanical response than ACDF, although the exact pattern depends on the implant design. Anterior and posterior column load-sharing patterns were different between the two implants and may affect implant selection based on the anatomical and pathological state at the index and adjacent levels.
The objective of this study was to develop a finite element model of the lumbar spinal column of an eight-year-old human spine and compare flexibilities under pure moments, adult, and pediatric loading with different material models. The geometry was extracted from computed tomography scans. The model included the cortical and cancellous bones, growth plates, ligaments, and discs. Adult, adolescent, and pediatric material models were used. Flexion (8 Nm), extension (6 Nm), lateral bending (6 Nm), and axial rotation (4 Nm) moments representing adult loads were applied to the three material models. Pediatric loading (0.5 Nm) was applied under these loadings to the eight-year-old spine using adult and pediatric material models. Flexibilities depended on spinal level, loading mode, and material model. Outputs incorporating the pediatric material model responded with increased flexibilities compared to the adult and adolescent material models, with one exception. This was true for the adult and pediatric loading conditions. While the sagittal and coronal bending responses were not considerably different between the adult and pediatric loadings, axial rotation responses were greater under the adult loading. This model may be used to determine intrinsic responses, such as stresses and strains, for improved characterizations of the juvenile spine behavior.
The objective of the study was to determine the sensitivity of material properties of the juvenile spine to its external and internal responses using a finite element model under compression, and flexion-extension bending moments. The methodology included exercising the 8-year-old juvenile lumbar spine using parametric procedures. The model included the vertebral centrum, growth plates, laminae, pedicles, transverse processes and spinous processes; disc annulus and nucleus; and various ligaments. The sensitivity analysis was conducted by varying the modulus of elasticity for various components. The first simulation was done using mean material properties. Additional simulations were done for each component corresponding to low and high material property variations. External displacement/rotation and internal stress-strain responses were determined under compression and flexion-extension bending. Results indicated that, under compression, disc properties were more sensitive than bone properties, implying an elevated role of the disc under this mode. Under flexion-extension moments, ligament properties were more dominant than the other components, suggesting that various ligaments of the juvenile spine play a key role in modulating bending behaviors. Changes in the growth plate stress associated with ligament properties explained the importance of the growth plate in the pediatric spine with potential implications in progressive deformities.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.