With rapidly increasing traffic occupancy, intelligent transportation systems (ITSs) are a vital feature for urban areas. This paper analyses methods for estimating long (L > 10 m) vehicle speed and length using a self-developed system, equipped with two anisotropic magneto-resistive (AMR) sensors, and introduces a method for verifying the results. A well-known cross-correlation method of magnetic signatures is not appropriate for calculating the vehicle speed of long vehicles owing to limited resources and a long calculation time. Therefore, the adaptive signature cropping algorithm was developed and used with a difference quotient of a magnetic signature. An additional piezoelectric polyvinylidene fluoride (PVDF) sensor and video camera provide ground truth to evaluate the performances. The prototype system was installed on the urban road and tested under various traffic and weather conditions. The accuracy of results was evaluated by calculating the mean absolute percentage error (MAPE) for different methods and vehicle speed groups. The experimental result with a self-obtained data set of 600 unique entities shows that the average speed MAPE error of our proposed method is lower than 3% for vehicle speed in a range between 40 and 100 km/h.

Reliable cost-effective traffic monitoring stations are a key component of intelligent transportation systems (ITS). While modern surveillance camera systems provide a high amount of data, due to high installation price or invasion of drivers’ personal privacy, they are not the right technology. Therefore, in this paper we introduce a traffic flow parameterization system, using a built-in pavement sensing hub of a pair of AMR (anisotropic magneto resistance) magnetic field and MEMS (micro-electromechanical system) accelerometer sensors. In comparison with inductive loops, AMR magnetic sensors are significantly cheaper, have lower installation price and cause less intrusion to the road. The developed system uses magnetic signature to estimate vehicle speed and length. While speed is obtained from the cross-correlation method, a novel vehicle length estimation algorithm based on characterization of the derivative of magnetic signature is presented. The influence of signature filtering, derivative step and threshold parameter on estimated length is investigated. Further, accelerometer sensors are employed to detect when the wheel of vehicle passes directly over the sensor, which cause distorted magnetic signatures. Results show that even distorted signatures can be used for speed estimation, but it must be treated with a more robust method. The database during the real-word traffic and hazard environmental condition was collected over a 0.5-year period and used for method validation.

Seeking an effective method for estimating the speed and length of a car is still a challenge for engineers and scientists who work on intelligent transportation systems. This paper focuses on a self-developed system equipped with four anisotropic magneto-resistive (AMR) sensors which are placed on a road lane. The piezoelectric polyvinylidene fluoride (PVDF) sensors are also mounted and used as a reference device. The methods applied in the research are well-known: the fixed threshold-based method and the adaptive two-extreme-peak detection method. However, the improved accuracy of estimating the length by using one of the methods, which is based on computing the difference quotient of a time-discrete signal (representing the changes in the magnitude of the magnetic field of the Earth), is observed. The obtained results, i.e., the speed and length of a vehicle, are presented for various values of the increment Δn used in numerical differentiation of magnetic field magnitude data. The results were achieved in real traffic conditions after analyzing a data set M = 290 of vehicle signatures. The accuracy was evaluated by calculating MAE (Mean Absolute Error), RMSE (Root Mean Squared Error) for different classes of vehicles. The MAE is within the range of 0.52 m–1.18 m when using the appropriate calibration factor. The results are dependent on the distance between sensors, the speed of vehicle and the signal processing method applied.

This article explores a non-invasive method to determine interstitial fluid level and pressure in tissue. Interdigital electrodes were chosen by simulated results in software “Comsol multiphysis 4.3a”. Environment model similar to human body was created. Measurements were carried out at different situations which can occur during preoperative and afterwards surgery. Non-invasive method decreases possibility of infection and will improve recovery process in postoperative period.

Magnetic field sensors installed in the road infrastructure can be used for autonomous traffic flow parametrization. Although the main goal of such a measuring system is the recognition of the class of vehicle and classification, velocity is the essential parameter for further calculation and it must be estimated with high reliability. In-field test campaigns, during actual traffic conditions, showed that commonly accepted velocity estimation methods occasionally produce highly erroneous results. For anomaly detection, we propose a criterion and two different correction algorithms. Non-linear signal rescaling and time-based segmentation algorithms are presented and compared for faulty result mitigation. The first one consists of suppressing the highly distorted signal peaks and looking for the best match with cross-correlation. The second approach relies on signals segmentation according to the feature points and multiple cross-correlation comparisons. The proposed two algorithms are evaluated with a dataset of over 300 magnetic signatures of a vehicle from unconstraint traffic conditions. Results show that the proposed criteria highlight all greatly faulty results and that the correction algorithms reduce the maximum error by twofold, but due to the increased mean error, mitigation technics shall be used explicitly with distorted signals.