The ability to study the adsorption behavior of surfactant species is of interest in the field of enhanced oil recovery (EOR), especially pertaining to alkaline surfactant flooding. In this work, a calcite model mineral surface was obtained by electrochemically assisted deposition. This was achieved via the nitrate and/or oxygen electroreduction reactions in the presence of bicarbonate and calcium ions, by which controlled deposition of calcium carbonate was effected on a quartz crystal microbalance sensor covered with an electroactive gold layer. In addition, the effect of pH and Ca 2+ concentration on the effective surface charge of the deposited calcite particles was mapped. Calcite-modified sensors were used in conjunction with a quartz crystal microbalance with dissipation monitoring to study the effect of Na + and Ca 2+ concentration on the adsorption behavior of an anionic alcohol alkoxy sulfate (AAS) surfactant. Adsorption of the surfactant remained indifferent to ionic concentrations around the isoelectric point of calcite. Still, electrostatics play an important role in this regard, and it is essential to decrease the Ca 2+ concentration sufficiently to minimize AAS adsorption. The results from this study show that a relatively simple method allows for the controlled deposition of a model rock surface, and there is ample opportunity to extend the work to other metal oxide surface types, including complex mixtures as can be obtained by co-deposition. Furthermore, the findings from these adsorption studies aid in the determination of optimal flooding parameters, with the aim to increase the efficiency and efficacy of EOR.

Siloprene-based, ion-selective membranes (ISMs) were drop-casted onto a field-effect transistor device that consisted of a single-chip array of top-down prepared silicon nanowires (SiNWs). Within one array, two sets of SiNWs were covered with ISMs, each containing two different ionophores, allowing the simultaneous sensing of K and Na ions using a flow cell. It is shown that both ions can be effectively detected in the same solution over a wide concentration range from 10(-4) to 10(-1) M without interference. The ISMs were also analyzed in a conventional ISE configuration, allowing a direct comparison. While the responses for K(+) were similar for both sensor configurations, remarkably, the Na(+) response of the ISM-covered SiNW device was found to be higher than the one of the ISE configuration. The addition of a Na(+) buffering hydrogel layer between the SiO2 of the SiNW and the ISM reduced the response, showing the importance of keeping the boundary potential at the SiO2/ISM interface constant. The responses of the siloprene-covered SiNW devices were found to be stable over a period of at least 6 weeks, showing their potential as a multichannel sensor device.

Design and operation of a "six-flow fixed-bed microreactor" setup for Fischer-Tropsch synthesis (FTS) is described. The unit consists of feed and mixing, flow division, reaction, separation, and analysis sections. The reactor system is made of five heating blocks with individual temperature controllers, assuring an identical isothermal zone of at least 10 cm along six fixed-bed microreactor inserts (4 mm inner diameter). Such a lab-scale setup allows running six experiments in parallel, under equal feed composition, reaction temperature, and conditions of separation and analysis equipment. It permits separate collection of wax and liquid samples (from each flow line), allowing operation with high productivities of C5+ hydrocarbons. The latter is crucial for a complete understanding of FTS product compositions and will represent an advantage over high-throughput setups with more than ten flows where such instrumental considerations lead to elevated equipment volume, cost, and operation complexity. The identical performance (of the six flows) under similar reaction conditions was assured by testing a same catalyst batch, loaded in all microreactors. © 2013 AIP Publishing LLC. [http://dx

Capacitors made of interdigitated electrodes (IDEs) as a transducer platform for the sensing of volatile organic compounds (VOCs) have advantages due to their lower power operation and fabrication using standard micro-fabrication techniques. Integrating a micro-electromechanical system (MEMS), such as a microhotplate with IDE capacitor, further allows study of the temperature- dependent sensing response of VOCs. In this paper, the design, fabrication, and characterization of a low-power MEMS microhotplate with IDE capacitor to study the temperature-dependent sensing response to methanol using Zeolitic imidazolate framework (ZIF-8), a class of metal-organic framework (MOF), is presented. A Titanium nitride (TiN) microhotplate with aluminum IDEs suspended on a silicon nitride membrane is fabricated and characterized. The power consumption of the ZIF-8 MOF-coated device at an operating temperature of 50 ∘ C is 4.5 mW and at 200 ∘ C it is 26 mW. A calibration methodology for the effects of temperature of the isolation layer between the microhotplate electrodes and the capacitor IDEs is developed. The device coated with ZIF-8 MOF shows a response to methanol in the concentration range of 500 ppm to 7000 ppm. The detection limit of the sensor for methanol vapor at 20 ∘ C is 100 ppm. In situ study of sensing properties of ZIF-8 MOF to methanol in the temperature range from 20 ∘ C to 50 ∘ C using the integrated microhotplate and IDE capacitor is presented. The kinetics of temperature-dependent adsorption and desorption of methanol by ZIF-8 MOF are fitted with double-exponential models. With the increase in temperature from 20 ∘ C to 50 ∘ C, the response time for sensing of methanol vapor concentration of 5000 ppm decreases by 28%, whereas the recovery time decreases by 70%.

No abstract