Fusion of the diaroylethanes with phosphorus pentasulfide produces the 2,5diarylthiophenes. By this method, Kapf and Paal (1) claimed the preparation of 2,5-diphenylthiophene in 60% yield. Holleman (2) also synthesized 2,5-di-ptolylthiophene by this procedure. The reaction is generally unsatisfactory, due to tarry products and unpredictable yields. Since phosphorus pentasulfide acts 1405
NOTES 989The following points about the chemical work are worthy of comment. 1. The addition of a small amount of acetic acid facilitated the reaction of thiosemicarbazide with the carbonyl compounds; so that it was essentially complete in one-half to one hour. Anderson, et aLI4 reported the reaction time to vary from 8 to 80 hours when no acetic acid was added. 2. The synthesis of 5-chloro-2-thenaldehyde in 50-55% yield by formylation of thiophene with N-methylformanilide was recently reported.1° It was therefore interesting to carry out the synthesis of this compound by the Sommelet procedure, in order to compare the yields by the two methods. When 5-chloro-2-methylthiophene was converted to the thenyl bromide with N-bromosuccinimide, and thence to the aldehyde, a 33y0 yield was obtained. When 2-chlorothiophene was chloromethylated by the procedure of Cairns and McKusick" and the thenyl chloride converted to the aldehyde, a 25% yield was obtained. Thus neither process is as efficient as the formylation procedure. lo Experimental Thiosemicarbaz0nes.-The general procedure for the preparation of all the thiosemicarbazones was as follows: 0.1 mole of the carbonyl compound was dissolved in 100 ml. of 50% ethanol (95% ethanol was used for the less soluble compounds) and approximately 2 ml. of glacial acetic acid and 9.1 g. (0.10 mole) of thiosemicarbazide added. The solution was warmed with occasional swirling until the thiosemicarbazide dissolved and then refluxed for approximately one hour. After cooling, the crystalline thiosemicarbazone was collected and recrystallized from 50% ethanol or methanol. The crude yields ranged from 90-96%. The thiosemicarbazones are all 'yellow crystalline compounds, but occasionally on fresh crystallization, some of them appear almost white. After drying and exposure to air, however, they assume a yellow tinge.Intermediate Carbonyl Compounds.-Although all of the thenaldehydes and acetothienones have been previously reported, some of them were prepared by methods not previously applied to these compounds and these are briefly described. 3-Thenaldehyde was prepared by the Sommelet procedure, as previously described.l2 as were 2-chloro-, 2bromo-, and 2,5-dichlor0-3-thenaldehyde.l* In the latter case, 54 g. (59%) of crude 2,5-dichloro-3-thenaldehyde was obtained from 108 g. (0.65 mole) of 2,5-dichloro-3-methylthiophene and 0.6 mole of N-bromosuccinimide, which is a considerable improvement over the yield previously reported, although no changes were made in the procedure. 5-Nitro-2-thenaldehyde was prepared by the method of Patrick and Emerson.14 The observation of Dullaghan, et aZ.,16 that this compound could not be obtained by application of the Sommelet procedure to the product obtained on treatment of 5-nitro-2-methylthiophene with N-bromosuccinimide was confirmed.5-Methyl-, 3-methyl-, 5-t-butyl-and 5-acetamido-2thenaldehyde were obtained by the dimethylformamide formylation procedure described by Campaigne and Archer .I6 The various 2-acetothienones were samples previously prepared ...
Newman and Caflisch3 recently reported that the sodium salt of 1-benzene sulphonyl-2-benzoylhydrazine decomposed in ethylene glycol at 160°in the presence of a surface-active catalyst to give benzaldehyde in high yield.
Thiofluorenone 769 2-Amino-4-methyl-5-thioformamidomethylpyrimidine (XI).-To 1.8 g. (0.01 mole) of the hydrochloride of X dissolved in 5 cc. of water and cooled below 15°a solution of 1.2 g. of potassium carbonate in 4.0 cc. of water was added as rapidly as possible with cooling. A solution of 1.2 g. of potassium dithioformate in 3.5 cc. of water was added immediately and the mixture was stirred for four hours at room temperature. The solid material was isolated by filtration and washed with water. The washed product was dissolved in 8 cc. of 50 ( acetic acid and filtered from a small amount of insoluble material. The warm solution was neutralized with ammonium hydroxide (sp. gr. 0.89), cooled, and filtered. The dried solid, which had a slightly green east, weighed 1.3 g. (71%), m. p. 192-198°. After two recrystallizations from water, XI melted at 212-213°.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.