Nocturnal bite force during sleep associated bruxism was measured in 10 subjects. Hard acrylic dental appliances were fabricated for the upper and lower dentitions of each subject. Miniature strain-gauge transducers were mounted to the upper dental appliance at the right and left first molar regions. In addition, thin metal plates that contact the strain-gauge transducers were attached to the lower dental appliance. After a 1-week familiarization with the appliances, nocturnal bite force was measured for three nights at the home of each subject. From the 30 recordings, 499 bruxism events that met the definition criteria were selected. The above described system was also used to measure the maximum voluntary bite forces during the daytime. The mean amplitude of detected bruxism events was 22.5 kgf (s.d. 13.0 kgf) and the mean duration was 7.1 s (s.d. 5.3 s). The highest amplitude of nocturnal bite force in individual subjects was 42.3 kgf (15.6-81.2 kgf). Maximum voluntary bite force during the daytime was 79.0 kgf (51.8-99.7 kgf) and the mean ratio of nocturnal/daytime maximum bite force was 53.1% (17.3-111.6%). These data indicate that nocturnal bite force during bruxism can exceed the amplitude of maximum voluntary bite force during the daytime.

Some metallic materials in dental prostheses may cause allergic hypersensitivity. Symptoms appear not only in the oral cavity, but also on hands, feet or the entire body. Release of metal ions is thought to cause the allergic reactions; micro-particles of the corrosion products of the metal and/or ionic metal hydroxides/oxides may be the allergens. The study purpose was to review clinical surveillance of dental allergic hypersensitivity in our dental hospital. From July 2000 to June 2005, 212 patients with suspected dental metal allergy were patch tested with 26 reagents, including 19 ready-made patch test reagents (Patch test reagents™, Torii Pharmaceutical Corporation, Tokyo, Japan) and 9 custom-made reagents. One-hundredand-sixty-seven patients were females (78.8%) and 45 patients were males (21.2%). A total of 148 patients (69.8%) had one or more positive patch test reactions. The most common allergens were nickel (25.0%), palladium (24.4%), chromium (16.7%), cobalt (15.9%) and stannum (12.5%). Typical allergic symptoms and diagnoses were Pustulosis palmaris et plantaris, lichen planus, stomatitis and contact dermatitis. This study indicates that dentists and dental researchers should be concerned about the allergenic potential of dental metal materials.

No abstract

The purpose of this study was to assess the influence of an experimentally induced light premature occlusal contact on tooth sensation. This assessment involved monitoring the electric tooth pain threshold (TPT) at multiple times before and after altering the occlusal contact. This alteration was produced by placing high inlays, which were measured with a custom made measuring device in maximum intercuspation. Data were collected on 10 teeth in 5 subjects, all whom were male and between the ages of 24 and 30 years. The contact area of the high inlays varied from 75 microm to 193 microm. The TPT changes in these teeth ranged from -43 to +21% of their baseline level. Seven of these teeth showed a significant decrease (P < 0.05) in the TPT, one showed an increase and two did not show a significant change. Two of the teeth with a decreased TPT had cold water triggered occlusal pain, and 2 teeth had only occlusal pain. After several inlay adjustments to eliminate interference in maximum intercuspation, all tested teeth returned to their TPT baseline level and all symptoms disappeared. These results suggested that a light premature occlusal contact may change tooth sensation.

The aims of this study were to develop a device for measuring the tightness of proximal tooth contact and to evaluate the proximal contact tightness using this device at rest and during clenching. Twenty young adult volunteers with healthy dentition participated in this experiment. The tightness of proximal tooth contact between the second premolar and the first molar of both the maxilla and the mandible was measured by pulling a stainless steel strip between them at rest, and at 20 and 50% clenching levels of maximum voluntary contraction of masseter muscles at intercuspal position. Proximal contact tightness increased as the clenching levels of both the maxilla and the mandible increased. At rest, proximal contact tightness was less in the maxilla than in the mandible, whereas during clenching it was less in the mandible. These results indicate that during clenching, the teeth are displaced and they contact appropriately with adjacent teeth, making it possible to exert sufficient occlusal force while maintaining the integrity of dental arches.