This study conducted a radial flow experiment to investigate the existence of non-Darcy flow and calculate the non-Darcy “inertia” coefficient; the experiment was performed on seven cylindrical perforated artificial porous media samples. Two hundred thirty-one runs were performed, and the pressure drop was reported. The non-Darcy coefficient β was calculated and compared with available in the literature. The results showed that the non-Darcy coefficient decreased nonlinearly and converged on a value within a specific range as the permeability increased. Nonetheless, it was found that the non-Darcy flow exists even in the very low flow rate deployed in this study. In addition, it has been found that the non-Darcy effect is not due to turbulence but also the inertial effect. The existence of a non-Darcy flow was confirmed for all the investigated samples. The Forchheimer numbers for airflow at varied flow rates are determined using experimentally measured superficial velocity, permeability, and non-Darcy coefficient.
An oil well's productivity is generally considered the standard measure of the well's performance. However, productivity depends on several factors, including fluid characteristics, formation damage, the reservoir's formation, and the kind of completion the well undergoes. How a partial completion can affect a well's performance will be investigated in detail in this study, as nearly every vertical well is only partially completed as a result of gas cap or water coning issues. Partially penetrated wells typically experience a larger pressure drop of fluid flow caused by restricted regions, thus increasing the skin factor. A major challenge for engineers when developing completion designs or optimizing skin factor variables is devising and testing suitable partial penetration skin and comparing completion options. Several researchers have studied and calculated a partial penetration skin factor, but some of their results tend to be inaccurate and cause excessive errors. The present work proposes experimental work and a numerical simulation model for accurate estimation of the pseudo-skin factor for partially penetrated wells. The work developed a simple correlation for predicting the partial penetration skin factor for perforated vertical wells. The work also compared the results from available models that are widely accepted by the industry as a basis for gauging the accuracy of the new correlation in estimating the skin factor. Compared to other approaches, the novel correlation performs well by providing estimates for the partial penetration skin factor that are relatively close to those obtained by the tested models. This work's main contribution is the presentation of a novel correlation that simplifies the estimation of the partial penetration skin factor in partially completed vertical wells.
A number of different factors can affect flow performance in perforated completions, such as perforation density, perforation damage, and tunnel geometry. In perforation damage, any compaction at the perforation tunnels will lead to reduced permeability, more significant pressure drop, and lower productivity of the reservoir. The reduced permeability of the crushed zone around the perforation can be formulated as a crushed-zone skin factor. For reservoir flow, earlier research studies show how crushed (compacted) zones cause heightened resistance in radially converging vertical and horizontal flow entering perforations. However, the effects related to crushed zones on the total skin factor are still a moot point, especially for horizontal flows in perforations. Therefore, the present study will look into the varied effects occurring in the crushed zone in relation to the vertical and horizontal flows. The experimental test was carried out using a geotechnical radial flow set-up to measure the differential pressure in the perforation tunnel with a crushed zone. Computational fluid dynamics (CFD) software was used for simulating pressure gradient in a cylindrical perforation tunnel. The single-phase water was radially injected into the core sample with the same flow boundary conditions in the experimental and numerical procedures. In this work, two crushed zone configuration scenarios were applied in conjunction with different perforation parameters, perforation length, crushed zone radius, and crushed zone permeability. In the initial scenario, the crushed zone is assumed to be located at the perforation tunnel’s side only, while in the second scenario, the crushed zone is assumed to be located at a side and the tip of perforation (a tip-crushed zone). The simulated results indicate a good comparison with regard to the two scenarios’ pressure gradients. Furthermore, the simulations’ comparison reveals another pressure drop caused by the tip crushed zone related to the horizontal or plane flow in the perforations. The differences between the two simulations’ results show that currently available models for estimating the skin factor for vertical perforated completions need to be improved based on which of the two cases is closer to reality. This study has presented a better understanding of crushed zone characteristics by employing a different approach to the composition and shape of the crushed zone and permeability reduction levels for the crushed zone in the axial direction of the perforation.
Oil and gas well productivity can be affected by a number of different skin factors, the combined influences of which contribute to a well’s total skin factor. The skin caused by deviated wells is one such well-known factor. The present study aimed to investigate skin effects caused by deviated well slants when considering vertical-to-horizontal permeability anisotropy. The research employed computational fluid dynamics (CFD) software to simulate fluid flows in inclined wells through the injection of water with Darcy flow using 3D geometric formations. The present work investigates the effects of four main characteristics—namely, the permeability anisotropy, wellbore radius, reservoir thickness, and deviation angle—of open-hole inclined wells. Additional investigations sought to verify the effect of the direction of perforations on the skin factor or pressure drop in perforated inclined wells. In the case of an inclined open hole well, the novel correlation produced in the current study simplifies the estimation of the skin factor of inclined wells at different inclination angles. Our comparison indicates good agreement between the proposed correlation and available models. Furthermore, the results demonstrated a deviation in the skin factor estimation results for perforated inclined wells in different perforation orientation scenarios; therefore, existing models must be improved in light of this variance. This work contributes to the understanding and simulation of the effects of well inclination on skin factor in the near-wellbore region.
Evaluating petroleum reserves requires an initial investigation of the relevant petrophysical characteristics of a target area's sandstones. In general, the most common type of host rocks represented in the hydrocarbon reservoirs are sedimentary rocks, which includes sandstone. This paper presents a technique for preparing four homogenises synthetic sandstone samples that can be applied in the hydrocarbon recovery projects. The approach mixes sand together with epoxy glue and can be employed in the evaluation of synthetic sand plug characteristics and then compared with fine-grained sandstone sample. The study conducted extensive laboratory testing using lab-created synthetic sandstone samples of four sandstone grain sizes. The three synthetic sandstone samples were made from four different sandstone grain sizes, and one sample was a mixture of two different grain size with various amount of epoxy. Mercury intrusion porosimetry (MIP) and scanning electron microscopy (SEM) have been used to first characterize and then analyze the pore morphology and index properties for the synthetic samples. The index properties included permeability, porosity, median pore diameter, tortuosity, and pore size distribution. The experimental results indicated that weak solidified sandstone index characteristics are strongly affected by both mixing and grain size. In addition, SEM map images revealing pore morphologies and homogenises grain distribution of the tested samples indicate that grains that undergo reductions in size require additional epoxy glue content, likely due to binder distribution of glue among the small grains.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.