No abstract

In this work, pure BiFeO3 and samples doped with different concentrations of chromium were synthesized to improve the optical properties and efficiency of solar cells based on BiFeO3. The sol-gel method was used for synthesis due to its ability to produce nanostructured materials with high purity and good homogeneity, as well as the possibility of controlling the size and shape of the resulting particles. The samples were characterized by different analytical techniques. Thermal analysis results indicate that the dopant increases the weight loss of the sample from 61 to 81%, with an increase in the exothermal in the nucleation and crystallization temperature range. The X-ray diffraction patterns and UV-visible spectra show a dependence of the crystallite size and bandgap with respect to the amount of Cr dopant, decreasing from 168 to 73 nm and from 2.14 to 1.92 eV, respectively. Scanning electron microscopy images display a decreasing grain size as a result of an increasing amount of dopant. The I-V analysis results show a 1% Cr-doped BiFeO3 photovoltaic device exhibits enhanced photovoltaic performance with higher photocurrent and 4.17 times greater energy conversion efficiency compared with a pure BiFeO3 photovoltaic device. For their behavior, Cr-doped BiFeO3-based photoelectrodes are very promising materials for photovoltaic devices.

Arsenic (As) contamination of water is a serious problem in developing countries. In water streams, arsenic can be as As(V) and As(III), the latter being the most toxic species. In this work, an innovative adsorbent based on CaTiO3 nanoparticles (CTO) was prepared by the sol-gel technique for the removal of As(III) from aqueous solution. X-ray diffraction of the CTO nanoparticles powders confirmed the CTO phase. Transmission electron microscopy observations indicated an average particle size of 27 nm, while energy dispersive X-ray spectroscopy analysis showed the presence of Ca, Ti, and O in the expected stoichiometric amounts. The surface specific area measured by Brunauer, Emmett, and Teller (BET) isotherm was 43.9 m2/g, whereas the isoelectric point determined by Zeta Potential measurements was at pH 3.5. Batch adsorption experiments were used to study the effect of pH on the equilibrium adsorption of As(III), using an arsenite solution with 15 mg/L as initial concentration. The highest removal was achieved at pH 3, reaching an efficiency of up to 73%, determined by X-ray fluorescence from the residual As(III) in the solution. Time dependent adsorption experiments at different pHs exhibited a pseudo-second order kinetics with an equilibrium adsorption capacity of 11.12 mg/g at pH 3. Moreover, CTO nanoparticles were regenerated and evaluated for four cycles, decreasing their arsenic removal efficiency by 10% without affecting their chemical structure. X-ray photoelectron spectroscopy analysis of the CTO surface after removal experiments, showed that arsenic was present as As(III) and partially oxidized to As(V).

Pure and Fe-doped TiO2 nanoparticles were synthesized by the sol–gel method. The samples were characterized by X-ray diffraction, Raman spectroscopy, BET, UV-vis diffuse reflectance spectroscopy, and scanning electron microscopy. The results show a dependence between the crystallite size and the amount of dopant, which decreases from 13.02 to 12.81 nm. The same behavior was observed in the optical properties, where the band gap decreased from 3.2 to 2.86 eV. The arsenic (V) adsorption was tested in aqueous solution containing 5 mg/L of arsenic and 0.5 g/L of adsorbent at pH 7 and in dark conditions. The results indicate that the TiO2-B sample shows a higher arsenic removal, reaching 88% arsenic removal from the water at pH 7. Thus, it is also shown that the best performance occurs at pH 5, where it reaches an arsenic removal of 94%. Ion competition studies show that arsenic removal capacity is slightly affected by chloride, carbonate, nitrate, and sulfate ions. According to the results, the synthesized samples are a promising material for treating arsenic-contaminated water.

En el presente trabajo experimental se presenta los resultados preliminares obtenidos en el diseño, construcción y evaluación de dos sistemas de concentración solar para la generación de vapor de agua, estos son el Concentrador Solar Cilíndrico Parabólico (CCP), y el Reflector Solar Fresnel de Foco Lineal (RESFFOL). La evaluación se ha realizado bajo las condiciones de radiación solar y otros parámetros meteorológicos de la ciudad de Tacna, llegándose a determinar el área eficiente de la superficie reflectante, pérdidas de calor debido al ángulo de inclinación del concentrador, determinación de la eficiencia óptica, determinación del coeficiente global de pérdidas y la determinación de la eficiencia térmica, estos resultados nos indican la posibilidad de usar esta tecnología para el uso de la energía solar y producir vapor de agua a determinada temperatura y presión para múltiples usos, y posteriormente previa investigación para la generación de energía eléctrica.