A fibrous herringbone-modified helicoidal architecture is identified within the exocuticle of an impact-resistant crustacean appendage. This previously unreported composite microstructure, which features highly textured apatite mineral templated by an alpha-chitin matrix, provides enhanced stress redistribution and energy absorption over the traditional helicoidal design under compressive loading. Nanoscale toughening mechanisms are also identified using high load nanoindentation and in-situ TEM picoindentation. A Sinusoidally-Architected Helicoidal BiocompositeBy Nicholas A. Yaraghi, Nicolás Guarín-Zapata, Lessa K. Grunenfelder, Eric Hintsala, Sanjit Bhowmick, Jon M. Hiller, Mark Betts, Edward L. Principe, Jae-Young Jung, Leigh Sheppard, Richard Wuhrer, Joanna McKittrick, Pablo D. Zavattieri Keywords: (Composites, Toughness, Impact, Biomineral, Ultrastructure) Submitted to 3 Biologically mineralized composites offer inspiration for the design of next generation structural materials due to their low density, high strength and toughness currently unmatched by engineering technologies. [1][2][3][4][5][6][7][8][9] Such properties are based on the ability for the organism to utilize structural organics and acidic proteins to guide and control the mineralization process to yield hierarchical architectures with well-defined compositional gradients.One notable example is the highly developed raptorial appendage, or dactyl, of the stomatopods, a group of aggressive marine crustaceans that use these structures for feeding upon hard-shelled and soft-bodied prey. [10][11][12][13][14] The dactyls of the "smashers", those that feed primarily on hard-shelled prey, (see Figure 1A) takes the form of a bulbous club ( Figure 1B), which is used to smash through mollusk shells, crab exoskeletons, and other tough mineralized structures with tremendous force and speed. [11][12][13][14][15][16] Achieving accelerations over 10,000g and reaching speeds of 23 m/s from rest, the dactyl strike is recognized as one of the fastest and most powerful impacting events observed in Nature. [11,12] The club is capable of delivering and subsequently enduring repetitive impact forces up to 1500 N and cavitation stresses without catastrophically failing, demonstrating its utility as an exceptionally damage-tolerant natural material.The origins of such a mechanical response lie in the structural design. Previous work identified the club as a multi-regional composite material containing an organic matrix composed of alpha-chitin fibers mineralized by amorphous forms of calcium carbonate and calcium phosphate as well as crystalline apatite. [17,18] These investigations revealed mechanisms responsible for providing damage-tolerance and impact-resistance to the club, which were largely attributed to the interior of the club (periodic region), identified as the primary energy-absorbing layer. [17,18] The combination of soft polymeric nanofibers and stiffer mineral provides a periodic modulus mismatch leading to crack deflection, which in co...

Silicon is one of the most technologically important materials, used extensively in electronics, solar cells, micro-electro-mechanical systems (MEMS) based devices and more. Yet its mechanical properties are not well understood at the nanoscale where it is often utilized. Experimental measurements under a variety of loading conditions are needed, and compression experiments are particularly lacking. Here, the elastic-plastic response of 20 nm to 65 nm cubic Si nanocubes under uniaxial compression is investigated. The purely elastic limit of these nanocubes is observed to be up to 0.07 true strain at 7 GPa true stress with an upper yield point of 0.20 true strain and 11 GPa true stress. Investigation of the nature of dislocations generated during deformation of these nanocubes using post-mortem analysis in the TEM provides evidence that leading partial dislocations are the dominant source of plasticity at this scale.

Standard nanoindentation tests are ''high throughput'' compared to nearly all other mechanical tests, such as tension or compression. However, the typical rates of tens of tests per hour can be significantly improved. These higher testing rates enable otherwise impractical studies requiring several thousands of indents, such as high-resolution property mapping and detailed statistical studies. However, care must be taken to avoid systematic errors in the measurement, including choosing of the indentation depth/spacing to avoid overlap of plastic zones, pileup, and influence of neighboring microstructural features in the material being tested. Furthermore, since fast loading rates are required, the strain rate sensitivity must also be considered. A review of these effects is given, with the emphasis placed on making complimentary standard nanoindentation measurements to address these issues. Experimental applications of the technique, including mapping of welds, microstructures, and composites with varying length scales, along with studying the effect of surface roughness on nominally homogeneous specimens, will be presented.

No abstract

No abstract