A series of Eudragit RS PO-based hot melt extruded films were evaluated as potential transdermal systems, with particular emphasis on the inclusion of hydrophilic excipients to allow water sorption, which in turn would allow drug release on application to the skin. More specifically, sucrose, methyl cellulose, xanthan gum (Xantural®75), poloxamer (Pluronic®F127), Gelucire 44/14 were added to Eudragit RS PO and assessed in terms of physical structure (modulated temperature DSC (MTDSC), thermogravimetric analysis (TGA), powder XRD (PXRD), scanning electron microscopy(SEM)) and in vitro drug release and permeation properties. In addition, the effect of prior hydration on drug permeation was studied for selected systems. Phase separation was noted for sucrose, methylcellulose (high loading), xanthan gum (high loading), poloxamer and Gelucire 44/14 (high loading) using both visual observation and MTDSC. PXRD studies indicated drug crystallization within the phase separated systems. SEM studies broadly followed the same pattern. Dissolution studies indicated that the hydrophilic excipients considerably enhanced the release rate, while Franz diffusion cell studies showed a much greater variability in effectiveness, which we ascribe to the paucity of water of hydration present which would not allow swellable additives such as xanthan to release the drug. However, films containing Gelucire 44/14 emerged as the most satisfactory systems, despite the higher additive loaded systems showing drug phase separation. This may be related to emulsification rather than swelling on contact with water, as noted for the permeation studies involving prehydration. This strategy therefore presents a promising approach for triggered transdermal drug delivery, activated by hydration from the skin itself.

Oil shale is an important possible solution to the problem of energy in Jordan. To explore the technical and the economic feasibility of oil shale deposits, numerous samples are analyzed using the standard Fischer Assay (FA) method. However, it would be useful to develop faster, cheaper, and reliable methods for determining the oil content of oil shale. Therefore, the aim of this work was to propose and investigate rapid analytical techniques for the screening of oil shale deposits and to correlate them with the FA method. The Omari deposit located east of Jordan was selected as a case study for analysis using thermogravimetric analysis (TGA) coupled with Fourier-transform infrared (FTIR), differential scanning calorimetry (DSC), elemental analysis, X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray (EDX) analysis. Results obtained from the TGA method were linearly correlated with FA with high regression factor (R2 = 0.99); a quadratic correlation (R2 = 0.98) was maintained between the FA and the elemental hydrogen mass content, and a quadratic correlation (R2 = 0.97) was found between the FA and the aliphatic hydrocarbons (FTIR peak at 2927 cm−1) produced in the pyrolysis zone. Although other techniques were less correlated, further investigation might lead to better results. Subsequently, these correlated techniques can be a practical alternative to the conventional FA method when, in particular, specific correlation is made for each deposit.

Recently, consumer markets have shown great interest in sustainable products. Considerable research efforts are headed towards developing biodegradable and recyclable polymers and composites. In this study, the fabrication of a wood–plastic composite (WPC) via solid state compounding has been examined. Polyethylene terephthalate (PET) and wood sawdust waste as major components of waste and challenging materials for the manufacturing of WPCs have been explored. Furthermore, the addition of poly(ε-caprolactone) as a biodegradable plasticizing agent was investigated. Composite powders were prepared by cryogenic solid-state milling (cryomilling) according to a statistical mixture design. Mechanical and water absorption properties were inspected on film samples obtained by hot pressing. Different formulations resulted in a variety of colors, textures, water interactions and mechanical properties. A sawdust content of approximately 25 vol.% was optimal for the best combination of properties. The results indicated that cryomilling is technically advantageous in the production of WPCs.

No abstract

No abstract