Titanium and its alloys have been commonly used for biomedical implant applications for many years; however, associated high coefficient of friction, wear characteristics and low hardness have limited their long term performance. This article investigates the effects of the high speed laser surface modification of Ti6A1-4V on the microstructure, surface roughness, meltpool depth, phase transformation, residual strain, microhardness, and chemical composition. Laser treatment was carried out using a 1.5 kW CO 2 laser in an argon gas environment. Irradiance and residence time were varied between 15.7 to 26.7 kW/mm 2 and 1.08 to 2.16 ms respectively. Laser treatment resulted in a 20 to 50 pm thick surface modified layer without cracks. An increase in residence time and irradiance resulted in higher depth of processing. Surface roughness was found to decrease with increase in both irradiance and residence time. Metallography showed that a martensite structure formed on the laser treated region producing acicular a-Ti nested within the aged p matrix. The laser treatment reduced volume percentage of p-Ti as compared to the non-treated surface. Lattice stains in the range of 0.81% to 0.91% were observed after laser surface modification. A significant increase in micro-hardness was recorded for all laser treated samples. Microhardness increased up to 760 HV 0 . 05 which represented a 67% increase compared to the bulk material. Energy Dispersive X-ray Spectroscopy (EDS) analysis showed that laser surface modification produced a more homogenous chemical composition of the alloying elements compared to the untreated bulk metal.

The success of any implant, dental or orthopaedic, is driven by the interaction of implant material with the surrounding tissue. In this context, the nature of the implant surface plays a direct role in determining the long term stability as physico-chemical properties of the surface affect cellular attachment, expression of proteins, and finally osseointegration. Thus to enhance the degree of integration of the implant into the host tissue, various surface modification techniques are employed. In this work, laser surface melting of titanium alloy Ti-6Al-4V was carried out using a CO 2 laser with an argon gas atmosphere. Investigations were carried out to study the influence of laser surface modification on the biocompatibility of Ti-6Al-4V alloy implant material. Surface roughness, microhardness, and phase development were recorded. Initial knowledge of these effects on biocompatibility was gained from examination of the response of fibroblast cell lines, which was followed by examination of the response of osteoblast cell lines which is relevant to the applications of this material in bone repair. Biocompatibility with these cell lines was analysed via Resazurin cell viability assay, DNA cell attachment assay, and alamarBlue metabolic activity assay. Laser treated surfaces were found to preferentially promote cell attachment, higher levels of proliferation, and enhanced bioactivity when compared to untreated control samples. These results demonstrate the tremendous potential of this laser surface melting treatment to significantly improve the biocompatibility of titanium implants in vivo.

Carbon nanostructures in various forms and sizes, and with different speciation properties have been prepared from graphite by Liquid Phase -Pulsed Laser Ablation (LP-PLA) using a high frequency Nd:YAG laser. High energy densities and pulse repetition frequencies of up to 10 kHz were used in this ablation process to produce carbon nanomaterials with unique chemical structures. Dynamic Light Scattering (DLS), micro-Raman and High-Resolution Transmission Electron Microscopy (HRTEM) were used to confirm the size distribution, morphology, chemical bonding, and crystallinity of these nanostructures. This article demonstrates how the fabrication process affects measured characteristics of the produced carbon nanomaterials. The obtained particle properties have potential use for various applications including biochemical speciation applications.

A 1.5-kW CO 2 laser in pulsed mode at 3 kHz was used to investigate the effects of varied laser process parameters and resulting morphology of AISI 316L stainless steel. Irradiance and residence time were varied between 7.9 to 23.6 MW/cm 2 and 50 to 167 µs respectively. A strong correlation between irradiance, residence time, depth of processing and roughness of processed steel was established. The high depth of altered microstructure and increased roughness were linked to higher levels of both irradiance and residence times. Energy fluence and surface temperature models were used to predict levels of melting occurring on the surface through the analysis of roughness and depth of the region processed. Microstructural images captured by the SEM revealed significant grain structure changes at higher irradiances, but due to increased residence times, limited to the laser in use, the hardness values were not improved.

No abstract