Dye-sensitized solar cells (DSSCs) are an efficient photovoltaic technology for powering electronic applications such as wireless sensors with indoor light. Their low cost and abundant materials, as well as their...

We report thin-film InAs/GaAs quantum dot (QD) solar cells with n − i − p + deep junction structure and planar back reflector fabricated by epitaxial lift-off (ELO) of full 3-inch wafers. External quantum efficiency measurements demonstrate twofold enhancement of the QD photocurrent in the ELO QD cell compared to the wafer-based QD cell. In the GaAs wavelength range, the ELO QD cell perfectly preserves the current collection efficiency of the baseline single-junction ELO cell. We demonstrate by full-wave optical simulations that integrating a micro-patterned diffraction grating in the ELO cell rearside provides more than tenfold enhancement of the near-infrared light harvesting by QDs. Experimental results are thoroughly discussed with the help of physics-based simulations to single out the impact of QD dynamics and defects on the cell photovoltaic behavior. It is demonstrated that non radiative recombination in the QD stack is the bottleneck for the open circuit voltage (V oc ) of the reported devices. More important, our theoretical calculations demonstrate that the V oc offest of 0.3 V from the QD ground state identified by Tanabe et al., 2012, from a collection of experimental data of high quality III-V QD solar cells is a reliable -albeit conservative -metric to gauge the attainable V oc and to quantify the scope for improvement by reducing non radiative recombination. Provided that material quality issues are solved, we demonstrate -by transport and rigorous electromagnetic simulations -that light-trapping enhanced thin-film cells with twenty InAs/GaAs QD layers reach efficiency higher than 28% under unconcentrated light, ambient temperature. If photon recycling can be fully exploited, 30% efficiency is deemed to be feasible.

We report on the fabrication of diffraction gratings for application as back contact reflectors. The gratings are designed for thin-film solar cells incorporating absorbers with bandgap slightly lower than GaAs, i.e. InAs quantum dot or GaInNAs solar cells. Light trapping in the solar cells enables the increase of the absorption leading to higher short circuit current densities and higher efficiencies. We study metal/polymer back reflectors with half-sphere, blazed, and pyramid gratings, which were fabricated either by photolithography or by nanoimprint lithography. The gratings are compared in terms of the total and the specular reflectance, which determine their diffraction capabilities, i.e. the feature responsible for increasing the absorption. The pyramid grating showed the highest diffuse reflection of light compared to the half-sphere structure and the blazed grating. The diffraction efficiency measurements were in agreement with the numerical simulations. The validated model enables designing such metal/polymer back reflectors for other type of solar cells by refining the optimal dimensions of the gratings for different wavelength ranges.

Achieving strong absorption of low-energy photons is one of the key issues to demonstrate quantum dot solar cells working in the intermediate band regime at practical concentration factors and operating temperatures. Guided-mode resonance effects may enable large enhancement of quantum dot intraband optical transitions. We propose quantum dot thin-film cells designed to have significant field waveguiding in the quantum dot stack region and patterned at the rear-side with a sub-wavelength diffraction grating. Remarkable increase of the optical path length at mid-infrared wavelengths is shown owing to guided-mode resonances. Design guidelines are presented for energy and strength of the second-photon absorption for III-V quantum dots, such as InAs/GaAs and GaSb/GaAs, whose intraband and intersubband transitions roughly extends over the 2 - 8 µm range. The proposed design can also be applied to quantum dot infrared detectors. Angle-selectivity is discussed in view of applications in concentrator photovoltaic systems and infrared imaging systems.

Purpose Solar cells could make textile-based wearable systems energy independent without the need for battery replacement or recharging; however, their laundry resistance, which is prerequisite for the product acceptance of e-textiles, has been rarely examined. This paper aims to report a systematic study of the laundry durability of solar cells embedded in textiles. Design/methodology/approach This research included small commercial monocrystalline silicon solar cells which were encapsulated with functional synthetic textile materials using an industrially relevant textile lamination process and found them to reliably endure laundry washing (ISO 6330:2012). The energy harvesting capability of eight textile laminated solar cells was measured after 10–50 cycles of laundry at 40 °C and compared with light transmittance spectroscopy and visual inspection. Findings Five of the eight textile solar cell samples fully maintained their efficiency over the 50 laundry cycles, whereas the other three showed a 20%–27% decrease. The cells did not cause any visual damage to the fabric. The result indicates that the textile encapsulated solar cell module provides sufficient protection for the solar cells against water, washing agents and mechanical stress to endure repetitive domestic laundry. Research limitations/implications This study used rigid monocrystalline silicon solar cells. Flexible amorphous silicon cells were excluded because of low durability in preliminary tests. Other types of solar cells were not tested. Originality/value A review of literature reveals the tendency of researchers to avoid standardized textile washing resistance testing. This study removes the most critical obstacle of textile integrated solar energy harvesting, the washing resistance.