Alginate/hydroxyapatite composite scaffolds were developed using a novel production design. Hydroxyapatite (HAp) was incorporated into an alginate solution and internal gelling was induced by addition of slowly acid hydrolyzing d-gluconic acid delta-lactone (GDL) for the direct release of calcium ions from HAp. Hydrogels were then freeze-casted to produce a three-dimensional isotropic porous network. Scanning electron microscopy (SEM) observations, confocal laser scanning microscopy (CLSM) and microcomputed tomography (micro-CT) analysis of the scaffolds showed an optimal interconnected porous structure with pore sizes ranging between 100 and 300 microm and over 88% porosity. Proliferation assay and SEM observations demonstrated that human osteosarcoma cell lines were able to proliferate, maintain osteoblast-like phenotype and massively colonize the scaffold structure. Overall, these combined results indicate that the novel alginate based composites efficiently support the adhesion and proliferation of cells showing at the same time adequate structural and physical-chemical properties for being used as scaffolds in bone tissue engineering strategies.

In this study nano-composite scaffolds to be used as bone grafts have been endowed with antibacterial properties owing to the presence of silver nanoparticles. The alginate/hydroxyapatite composite scaffolds were prepared by internal gelation followed by a freeze-drying procedure to obtain a porous structure. The nanoparticles were prepared in presence of a lactose modified-chitosan and this colloidal solution was adsorbed on the scaffolds by exploiting electrostatic interactions. The adsorption and release of the silver from the composite scaffold was measured by ICP-AES and spectrofluorimetry measurements. Micro-computed tomography analysis of the scaffolds showed a homogeneous porous structure with average pore sizes of 341.5 μm and porosity of 80 %. In vitro biological tests (MTS and killing kinetics assays) demonstrated that silver does not affect the ability of the scaffolds to promote osteoblasts proliferation and that at the same time it exerts a strong bactericidal effect against both Gram+ and Gram- bacterial strains. Overall, the combined results indicate that these biocompatible antimicrobial scaffolds possess ideal characteristics for tissue engineering applications.

Titanium dioxide nanoparticles (TiO2NPs) suspensions (concentration 1.0 g/L) in synthetic sweat solution were applied on Franz cells for 24 h using intact and needle-abraded human skin. Titanium content into skin and receiving phases was determined. Cytotoxicity (MTT, AlamarBlue® and propidium iodide, PI, uptake assays) was evaluated on HaCat keratinocytes after 24 h, 48 h, and seven days of exposure. After 24 h of exposure, no titanium was detectable in receiving solutions for both intact and damaged skin. Titanium was found in the epidermal layer after 24 h of exposure (0.47 ± 0.33 μg/cm2) while in the dermal layer, the concentration was below the limit of detection. Damaged skin, in its whole, has shown a similar concentration (0.53 ± 0.26 μg/cm2). Cytotoxicity studies on HaCaT cells demonstrated that TiO2NPs induced cytotoxic effects only at very high concentrations, reducing cell viability after seven days of exposure with EC50s of 8.8 × 10−4 M (MTT assay), 3.8 × 10−5 M (AlamarBlue® assay), and 7.6 × 10−4 M (PI uptake, index of a necrotic cell death). Our study demonstrated that TiO2NPs cannot permeate intact and damaged skin and can be found only in the stratum corneum and epidermis. Moreover, the low cytotoxic effect observed on human HaCaT keratinocytes suggests that these nano-compounds have a potential toxic effect at the skin level only after long-term exposure.

Bisphenol A glycidylmethacrylate (BisGMA)/triethyleneglycol dimethacrylate (TEGDMA) thermosets and composites are well-known examples of biomaterials for dental applications that are receiving growing interest for orthopedic applications. While mechanical bulk properties are guaranteed by the presence of reinforcing fibers, in vitro and in vivo performances of these materials are ultimately driven by their ability to establish proper interactions between their surface and the surrounding tissues. Hence, the development of novel chemical processes enabling the introduction of bioactive molecules on the surface of these methacrylate-based thermosets is of particular interest. In the present work, we have devised a chemical strategy to expose carboxylic groups on the surface of the BisGMA/TEGDMA thermoset. The presence of negative charges was confirmed by Fourier transform infrared-attenuated total reflectance and by UV-vis spectrophotometry. Bulk mechanical properties and surface morphology of the thermoset were only slightly affected upon chemical functionalization. The activated material was further refined by the deposition of a lactose-modified chitosan (chitlac) driven by strong electrostatic interactions. The presence of the bioactive polysaccharide was confirmed by fluorescence spectroscopy and by confocal laser scanning microscopy measurements. Scratch tests were performed to evaluate the mechanical behavior of the coating. Finally, in vitro tests revealed that the presence of chitlac led to a slight enhancement of cell proliferation with respect to the unmodified BisGMA/TEGDMA thermoset. This effect was more pronounced when chitlac decorated with an arginine-glycine-aspartic acid (RGD) peptide was used in the preparation of the coating. In the latter case, the in vitro performance of the coated BisGMA/TEGDMA thermoset became comparable with that of clinically used roughened titanium.