Inflammatory processes can reliably be assessed by (19)F MRI using perfluorocarbons (PFCs), which is primarily based on the efficient uptake of emulsified PFCs by circulating cells of the monocyte-macrophage system and subsequent infiltration of the (19)F-labeled cells into affected tissue. An ideal candidate for the sensitive detection of fluorine-loaded cells is the biochemically inert perfluoro-15-crown-5 ether (PFCE), as it contains 20 magnetically equivalent (19)F atoms. However, the biological half-life of PFCE in the liver and spleen is extremely long, and so this substance is not suitable for future clinical applications. In the present study, we investigated alternative, nontoxic PFCs with predicted short biological half-lives and high fluorine content: perfluorooctyl bromide (PFOB), perfluorodecalin (PFD) and trans-bis-perfluorobutyl ethylene (F-44E). Despite the complex spectra of these compounds, we obtained artifact-free images using sine-squared acquisition-weighted three-dimensional chemical shift imaging and dedicated reconstruction accomplished with in-house-developed software. The signal-to-noise ratio of the images was maximized using a Nutall window with only moderate localization error. Using this approach, the retention times of the different PFCs in murine liver and spleen were determined at 9.4 T. The biological half-lives were estimated to be 9 days (PFD), 12 days (PFOB) and 28 days (F-44E), compared with more than 250 days for PFCE. In vivo sensitivity for inflammation imaging was assessed using an ear clip injury model. The alternative PFCs PFOB and F-44E provided 37% and 43%, respectively, of the PFCE intensities, whereas PFD did not show any signal in the ear model. Thus, for in vivo monitoring of inflammatory processes, PFOB emerges as the most promising candidate for possible future translation of (19)F MR inflammation imaging to human applications.

Background— Noninvasive detection of deep venous thrombi and subsequent pulmonary thromboembolism is a serious medical challenge, since both incidences are difficult to identify by conventional ultrasound techniques. Methods and Results— Here, we report a novel technique for the sensitive and specific identification of developing thrombi using background-free 19 F magnetic resonance imaging, together with α2-antiplasmin peptide (α2 AP )–targeted perfluorocarbon nanoemulsions (PFCs) as contrast agent, which is cross-linked to fibrin by active factor XIII. Ligand functionality was ensured by mild coupling conditions using the sterol-based postinsertion technique. Developing thrombi with a diameter <0.8 mm could be visualized unequivocally in the murine inferior vena cava as hot spots in vivo by simultaneous acquisition of anatomic matching 1 H and 19 F magnetic resonance images at 9.4 T with both excellent signal-to-noise and contrast-to-noise ratios (71±22 and 17±5, respectively). Furthermore, α2 AP -PFCs could be successfully applied for the diagnosis of experimentally induced pulmonary thromboembolism. In line with the reported half-life of factor XIIIa, application of α2 AP -PFCs >60 minutes after thrombus induction no longer resulted in detectable 19 F magnetic resonance imaging signals. Corresponding results were obtained in ex vivo generated human clots. Thus, α2 AP -PFCs can visualize freshly developed thrombi that might still be susceptible to pharmacological intervention. Conclusions— Our results demonstrate that 1 H/ 19 F magnetic resonance imaging, together with α2 AP -PFCs, is a sensitive, noninvasive technique for the diagnosis of acute deep venous thrombi and pulmonary thromboemboli. Furthermore, ligand coupling by the sterol-based postinsertion technique represents a unique platform for the specific targeting of PFCs for in vivo 19 F magnetic resonance imaging.

We demonstrate the use of photosensitive epoxy laminate TMMF S2045 for the fabrication and sealing of tapered microfluidic channels. The 45 μm thick resist enables the fabrication of shallow sealed cavities featuring extreme aspect ratios of less than 1:40 (h = 45 μm, w = 2000 μm). It also provides high resolution and enables minimum feature sizes of 10 μm. For the fabrication of free-standing structures, an aspect ratio of up to 7:1 was achieved. The dry-film photoresist can be applied easily by lamination onto structured substrates. The total thickness variation of the resist across a 100 mm wafer was determined to be less than ±0.6 μm. Process parameters for the fabrication and sealing of various micro-channels are discussed and optimized in this paper. The main focus was to minimize thermal impact during lamination, soft-bake, exposure and post-exposure bake, which could lead to lid sagging or channel clogging due to liquefaction of uncured resist. We tested TMMF according to ISO 10995-5 and found it to be non-cytotoxic, enabling its use for biological applications. Swelling of less than 5% for incubation of the dry-film resist in several biologically relevant solvents, buffers and cleaning solutions was observed.