The large meridional expansion turbine stator leads to complex secondary flows and heat transfer characteristics in the blade endwall region, while the upstream tip clearance leakage flow of the rotor makes it more complex in flow and heat transfer. The influence of the upstream rotor tip clearance on the large meridian expansion stator is worth studying. The flow and heat transfer characteristics of the downstream large meridional expansion turbine stator were studied by comparing the tip leakage flow of 1.5-stage shrouded and unshrouded turbines using a three-dimensional Reynolds-Averaged Navier-Stokes (RANS) solver for viscous turbulent flows. Validation studies were performed to investigate the aerodynamics and heat transfer prediction ability of the shear stress transport (SST) turbulence model. The influence of different tip clearances of the rotor including unshrouded blade heights of 0%, 1% and 5% and a 1% shrouded blade height were investigated through numerical simulation. The results showed that the upper passage vortex separation was more serious and the separation, and attachment point of horseshoe vortex in the pressure side were significantly more advanced than that of non-expansion turbines. The tip leakage vortex obviously increased the negative incidence angle at the downstream inlet. Furthermore, the strength of the high heat transfer zone on the suction surface of the downstream stator was significantly increased, while that of the shrouded rotor decreased.

In a high endwall angle turbine, large meridional expansion can cause the strong secondary flow at the endwall, which results in a larger endwall flow loss than the small meridional expansion turbine. The endwall heat transfer is strongly affected by secondary flow effect. In order to optimize the endwall flow to reduce the flow loss and optimize the distribution of heat load, the swept-curved method was used in this study. The swept-curved method was investigated on a transonic second stator (S2) with large meridional expansion in a Low-Pressure (LP) Turbine. Validation studies were performed to investigate the aerodynamic and the heat transfer prediction ability of shear stress transport (SST) turbulence model. The influence of different shapes of the stacking line, including forward-swept, backward-swept, positive-curved and negative-curved, were investigated through numerical simulation. The parameterized control of swept-curved height and angle were adopted to optimize the performance of the aerodynamic and heat transfer. 3D flow field calculation captured the relatively accurate flow structures in the parts of endwall and near endwall. Heat transfer behaviors were explored by means of isothermal wall temperature and Nusselt number (Nu) distribution. The results show that the maximal heat transfer coefficient at the leading edge, for the formation of horseshoe vortexes that cause the high velocity towards the endwall. The swept vane can improve the static pressure and heat load distribution at the endwall region, which decreases the area-averaged shroud heat flux by 2.6 percent and the loss coefficient 1.3 percent.

Flows in an intermediate turbine duct (ITD) connecting high-pressure turbines (HPT) and low-pressure turbines (LPT) are highly complex, influenced by the upstream HP turbine flow structures. Non-uniformities originating from the duct with struts of different sizes also affect the LPT inflow conditions, resulting in reduced efficiency. The goal of this paper is to provide detailed understanding of the flow physics and loss mechanisms within the ITDs for highly efficient ITD designs. Steady and unsteady numerical simulations of flows through the ITDs in the presence of HP blade and LP vane were conducted. Effects of upstream HP blade on flow fields and loss characteristics within the ITDs are explored. The generation and propagation of wake and secondary flows through the whole configuration is described, including the fast Fourier transformation (FFT) analyses of the flow in the ITD. Results from the numerical simulations show complex flow patterns resulted from blade-strut-vane flow interactions in a high-endwall-angle duct, which are not obtainable from ITD-only simulations. Moreover, the ITD has a strong amplifying effect on the distorted inflow, and the inflow with the upstream wake and secondary flows introduces a high loss area along the casing at ITD exit. Detailed results are presented and discussed for the flow physics and loss mechanisms within the ITD.

The flows in the power turbine and nonaxisymmetric exhaust volute with struts are closely coupled and inherently unsteady for marine gas turbines, and the flow interactions between them have a significant influence on the rotor and strut blade aerodynamic force characteristics; however, the asymmetric flow interactions have not been taken into account properly in current turbine design approaches. This paper is a continuation of the previous work and aims to clarify effects of different symmetrical and asymmetric layouts of struts on the flow interactions between power turbine and exhaust volute, in an attempt to seek an optimal layout of struts with the objective of making use of the mentioned asymmetric flow interactions to reduce the rotor and strut blade aerodynamic forces. This work was carried out using coupled unsteady simulations with the full annulus computational domain including 76 rotor blades, 9 strut blades, and an exhaust volute. Results show that the level of aerodynamic force at specific frequencies on the power turbine blade surface can be reduced by applying a proper distribution of asymmetric layout of struts; using the asymmetric strut design, although the reduction of the rotor blade aerodynamic force is weak, the strut blade aerodynamic force has been reduced significantly; the asymmetric layout of struts does not improve the overall flow characteristics of turbines very much. The present results indicate that it is possible to reduce vibration and increase blade fatigue life by asymmetric strut designs.

This paper is a continuation of the previous work, aiming to explore the influence of fillet configurations on flow and heat transfer in a large meridional expansion turbine. The endwall of large meridional expansion turbine stator has a large expansion angle, which leads to early separation of the endwall boundary layer, resulting in excessive aerodynamic loss and local thermal load. In order to improve the flow state and reduce the local high thermal load, five typical fillet distribution rules are designed. The three-dimensional Reynolds-Averaged Navier-Stokes (RANS) solver for viscous turbulent flows was used to investigate the different fillet configurations of the second stage stator blades of a 1.5-stage turbine, and which fillet distribution is suitable for large meridional expansion turbines. The influence of fillet structures on the vortex system and loss characteristics was analyzed, and its impact on wall thermal load was studied in detail. The fillet structure mainly affects the formation of horseshoe vortexes at the leading edge of the blade so as to reduce the loss caused by horseshoe vortexes and passage vortexes. The fillet structure suitable for the large meridional expansion turbine was obtained through the research. Reasonable fillet structure distribution can not only improve the flow state but also reduce the high thermal load on the wall surface of the meridional expansion turbine. It has a positive engineering guiding value.