The connective hard tissues bone and teeth are highly porous on a micrometer scale, but show high values of compression strength at a relatively low weight. The fabrication of porous materials has been actively researched and different processes have been developed that vary in preparation complexity and also in the type of porous material that they produce. Methodologies are available for determination of pore properties. The purpose of the paper is to give an overview of these methods, the role of porosity in natural porous materials and the effect of pore properties on the living tissues. The minimum pore size required to allow the ingrowth of mineralized tissue seems to be in the order of 50 µm: larger pore sizes seem to improve speed and depth of penetration of mineralized tissues into the biomaterial, but on the other hand impair the mechanical properties. The optimal pore size is therefore dependent on the application and the used material.

Adult cartilage has a limited healing capacity. Damages resulting from disease or injury increase over time and cause severe pain. One approach to reinstate the cartilage function is tissue engineering (TE). However, the generation of TE cartilage is time consuming and expensive and its properties are so far suboptimal. As in vivo cartilage is subject to loading, it is assumed that mechanical stimulation may enhance the quality of TE cartilage. In this study the short-term influence of variable compressive strain amplitudes on mechanical and biochemical properties of scaffold-free TE cartilage was investigated. Primary porcine chondrocytes were isolated, proliferated, redifferentiated, and transferred onto hydroxyapatite carriers, resulting in scaffold-free cartilage-carrier constructs. These constructs were placed in a custom-made bioreactor. Compression amplitudes of 5%, 10%, and 20% were applied. In each experiment four constructs were loaded with dynamic compression (3000 cycles/day, 1 Hz) for 14 days and four constructs served as unloaded control. The cartilage was evaluated biochemically, histological, and mechanically. No difference in glycosaminoglycan or collagen content between the loaded and the control groups was found. However, a positive correlation between compression amplitude and normalized Young's modulus was detected (R(2)=0.59, p<0.001). The highest compression amplitude of 20% had the strongest positive effect on the mechanical properties of the TE cartilage (Young's modulus increase of 241±28% compared to unloaded control). The data presented suggest that preconditioning with higher load amplitudes might be an attractive way of generating stiffer tissue and may help accelerating the cultivation of mechanically competent TE cartilage.

The implantation of osteochondral constructs-tissue-engineered (TE) cartilage on a bone substitute carrier-is a promising method to treat defects in articular cartilage. Currently, however, the TE cartilage's mechanical properties are clearly inferior to those of native cartilage. Their improvement has been the subject of various studies, mainly focusing on growth factors and physical loading during cultivation. With the approach of osteochondral constructs another aspect arises: the permeability of the carrier materials. The purpose of this study was to investigate whether and how the permeability of the subchondral bone influences the properties of native cartilage and whether the bone substitute carrier's permeability influences the TE cartilage of osteochondral constructs accordingly. Consequently, the influence of the subchondral bone's permeability on native cartilage was determined: Native porcine cartilage-bone cylinders were cultivated for 2 weeks in a bioreactor under mechanical loading with and without restricted permeability of the bone. For the TE cartilage these two permeability conditions were investigated using permeable and impermeable tricalciumphosphate carriers under equivalent cultivation conditions. All specimens were evaluated mechanically, biochemically, and histologically. The restriction of the bone's permeability significantly decreased the Young's modulus of native cartilage in vitro. No biochemical differences were found. This finding was confirmed for TE cartilage: While the biochemical parameters were not affected, a permeable carrier improved the cell morphology and mechanical properties in comparison to an impermeable one. In conclusion, the carrier permeability was identified as a determining factor for the mechanical properties of TE cartilage of osteochondral constructs.

The anatomy of the facet joint subchondral mineralized zone (SMZ) is the main parameter used in diagnosing osteoarthritis. Usually, a single CT scan slice is used to measure the thickness, but the measurement is highly location-dependent. Bone mineral density (BMD) and porosity could be more reliable than thickness for detecting SMZ sclerosis, and linking them to stiffness can provide insights into the mechanism of osteoarthritis progression. The goal of this study was two-fold: (1) to assess spatial heterogeneity in thickness, BMD, and porosity within the non-pathological human facet joint SMZ; (2) to correlate these measurements with the static modulus of elasticity (MOEsta ). Four non-pathological facet joints were excised and imaged using micro-computed tomography (µCT) to measure SMZ thickness, BMD, and porosity. A total of eight parallelepiped SMZ samples were similarly analyzed and then mechanically tested. The mean SMZ BMD, porosity, and thickness (± Standard Deviation) of the whole facet joints were 611 ± 35 mgHA/cc, 9.8 ± 1.3%, and 1.39 ± 0.41 mm, respectively. The mean BMD, porosity, and MOEsta of the eight SMZ samples were 479 ± 23 mgHA/cc, 12 ± 0.01%, and 387 ± 138 MPa, respectively, with a positive rank correlation between BMD and porosity. BMD and porosity were more homogeneous within the facet joint than thickness and they could be more reliable parameters than thickness for detecting SMZ sclerosis. The values for the physiological SMZ and MOEsta of human facets joints obtained here were independent of BMD. SMZ BMD and porosity were related to each other.

No abstract