The impact of the two seismic events of August 24th 2016 on the municipality of Amatrice was highly destructive. There were 298 victims, 386 injured, about 5000 homeless, and the historical center of the town suffered a great number of partial and total collapses. The 260 strong motion records obtained for the first event were analyzed and plotted in a shakemap, comparing them with the macroseismic damage surveys made in 305 localities. On the basis of an inspection survey made in September 2016, a map of the damage patterns of the buildings in the historical center was elaborated according to the EMS 98 classification. The damage level resulted very high with more than 60% of the inspected buildings showing partial or total collapse. The elevated level of destruction was mainly caused by the high vulnerability of the masonry buildings, mostly due to specific vulnerability factors such as the poor quality of masonry, the lack of connections between walls and the poor connection between external walls and floors.
A generalized cyclic steel model characterized by isotropic and kinematic hardening, inelastic buckling in compression and corrosion of rebars in reinforced concrete (RC) structures is presented. The model has been implemented in a fiber code, to perform seismic analyses of RC sections. The model is particularly accurate with respect to experimental cyclic behavior of rebars with buckling in compression when the strain does not exceed 1.5%. Twelve configurations of RC cross sections were selected as case studies for three geometries and different steel arrangements, assumed representative of RC columns or bridge piers (in a suitable scale). Each section was subjected to two groups of cyclic curvature histories representative of severe seismic loads, not far from collapse. Different axial loads and corrosion percentages (no corrosion, moderate, or high) have been selected to perform cyclic parametric analyses. One of the cases was taken from an experimental test on columns, deriving also steel characteristics used in all numerical cases. The results of the comparison among RC sections have been discussed. Numerical results show that the maximum compressive strain for steel rebars is always smaller than 1.5%, therefore the proposed steel model is accurate and represents a valid tool for structural assessment. Corrosion reduces RC section capacity, affecting various rebar mechanical characteristics, in particular buckling behavior.
In the present study, the incremental modal pushover analysis (IMPA), a pushover-based approach already proposed and applied to buildings by the same authors, was revised and proposed for bridges (IMPAβ). Pushover analysis considers the effects of higher modes on the structural response. Bridges are structurally very different from multi-story buildings, where multimodal pushover (MPA) has been developed and is currently used. In bridges, consideration for higher modes is often necessary: The responses of some structural elements of the bridge (e.g., piers) influence the overall bridge response. Therefore, the failure of these elements can determine the failure of the whole structure, even if they give a small contribution total base shear. Incremental dynamic analysis (IDA) requires input accelerograms for high intensities, which are rare in the databases, while scaling of generated accelerograms with a simple increment of the scaling acceleration is not appropriate. This fact renders IDA, which is by its nature time-consuming, not straightforward. On the contrary, the change of input spectrum required by IMPA is simple. IMPAβ also utilizes a simple complementary method coupled to MPA, to obtain bounds at very high seismic intensities. Finally, the two incremental methods based on static nonlinear and dynamic nonlinear analyses are compared.
This study presents the results of a refined numerical investigation meant at understanding the time‐dependent cyclic behavior of reinforced concrete (RC) bridge columns under chlorides‐induced corrosion. The chloride ingress in the cross‐section of the bridge column is simulated, taking into account the effects of temperature, humidity, aging, and corrosion‐induced cover cracking. Once the partial differential equations governing such multiphysics problem are solved through the finite‐element method, the loss of reinforcement steel bars cross‐section is calculated based on the estimated corrosion current density. The nonlinear cyclic response of the RC bridge column under corrosion is, thus, determined by discretizing its cross‐sections into several unidirectional fibers. In particular, the nonlinear modeling of the corroded longitudinal rebars exploits a novel proposal for the estimation of the ultimate strain in tension and also accounts for buckling under compression. A parametric numerical study is finally conducted for a real case study to unfold the role of corrosion pattern and buckling mode of the longitudinal rebars on the time variation of capacity and ductility of RC bridge columns.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2025 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.