CERN's Linac4 45 kV H-ion sources prototypes are installed at a dedicated ion source test stand and in the Linac4 tunnel. The operation of the pulsed hydrogen injection, RF sustained plasma and pulsed high voltages are described. The first experimental results of two prototypes relying on 2MHz RF-plasma heating are presented. The plasma is ignited via capacitive coupling, and sustained by inductive coupling. The light emitted from the plasma is collected by viewports pointing to the plasma chamber wall in the middle of the RF solenoid and to the plasma chamber axis. Preliminary measurements of optical emission spectroscopy and photometry of the plasma have been performed. The design of a cesiated ion source is presented. The volume source has produced a 45 keV H-beam of 16-22 mA which has successfully been used for the commissioning of the Low Energy Beam Transport (LEBT), Radio Frequency Quadrupole (RFQ) accelerator and chopper of Linac4.

The specifications set to the Linac4 ion source are: H-ion pulses of 0.5 ms duration, 80 mA intensity and 45 keV energy within a normalized emittance of 0.25 mmmrad RMS at a repetition rate of 2 Hz. In 2010, during the commissioning of a prototype based on H-production from the plasma volume, it was observed that the powerful co-extracted electron beam inherent to this type of ion source could destroy its electron beam dump well before reaching nominal parameters. However, the same source was able to provide 80 mA of protons mixed with a small fraction of H2+ and H3+ molecular ions. The commissioning of the radio frequency quadrupole accelerator (RFQ), beam chopper and H-beam diagnostics of the Linac4 are scheduled for 2012 and its final installation in the underground building is to start in 2013. Therefore, a crash program was launched in 2010 and reviewed in 2011 aiming at keeping the original Linac4 schedule with the following deliverables: Design and production of a volume ion source prototype suitable for 20-30 mA H-and 80 mA proton pulses at 45 keV by mid-2012. This first prototype will be dedicated to the commissioning of the low energy components of the Linac4. Design and production of a second prototype suitable for 40-50 mA H-based on an external RF solenoid plasma heating and cesiated-surface production mechanism in 2013 and a third prototype based on BNL's Magnetron aiming at reliable 2 Hz and 80 mA H-operations in 2014. In order to ease the future maintenance and allow operation with Ion sources based on three different production principles, an ion source "front end" providing alignment features, pulsed gas injection, pumping units, beam tuning capabilities and pulsed bipolar high voltage acceleration was designed and is being produced. This paper describes the progress of the Linac4 ion source program, the design of the Front end and first ion source prototype. Preliminary results of the summer 2012 commissioning are presented. The outlook on the future prototype ion sources is sketched. Abstract. The specifications set to the Linac4 ion source are: H -ion pulses of 0.5 ms duration, 80 mA intensity and 45 keV energy within a normalized emittance of 0.25 mmmrad RMS at a repetition rate of 2 Hz. In 2010, during the commissioning of a prototype based on H -production from the plasma volume, it was observed that the powerful co-extracted electron beam inherent to this type of ion source could destroy its electron beam dump well before reaching nominal parameters. However, the same source was able to provide 80 mA of protons mixed with a small fraction of H 2 + and H 3 + molecular ions. The commissioning of the radio frequency quadrupole accelerator (RFQ), beam chopper and H -beam diagnostics of the Linac4 are scheduled for 2012 and its final installation in the underground building is to start in 2013. Therefore, a crash program was launched in 2010 and reviewed in 2011 aiming at keeping the original Linac4 schedule with the following deliverables: Design and production of a volume ion source prototy...

Linac4 is a 160 MeV linear accelerator which will inject negative hydrogen ions (H−) into CERN's Proton Synchrotron Booster, a required upgrade to improve the beam brightness in the LHC injector chain. A volume production RF ion source, based on the design of the DESY RF source was implemented, but showed considerable electron dump ablation during operation at 45 keV beam energy. To reduce the electron beam power density in the dump, a magnetized Einzel lens is designed that reduces the beam energy to 10 keV before permanentmagnets dump the electrons on a tungsten surface. Presented in this paper are simulations of the design using IBSimu, the tunable range of parameters depending on the extracted H− and electron current, as well as details of the implementation, the choice of pulsed power converters and the electrode alignment system. In addition, simulations of proton extraction from this source will be shown. Abstract. Linac4 is a 160 MeV linear accelerator which will inject negative hydrogen ions (H − ) into CERN's Proton Synchrotron Booster, a required upgrade to improve the beam brightness in the LHC injector chain. A volume production RF ion source, based on the design of the DESY RF source was implemented, but showed considerable electron dump ablation during operation at 45 keV beam energy. To reduce the electron beam power density in the dump, a magnetized Einzel lens is designed that reduces the beam energy to 10 keV before permanent magnets dump the electrons on a tungsten surface. Presented in this paper are simulations of the design using IBSimu, the tunable range of parameters depending on the extracted H − and electron current, as well as details of the implementation, the choice of pulsed power converters and the electrode alignment system. In addition, simulations of proton extraction from this source will be shown. Presented at (NIBS

The common design practice of pressure vessels subjected to variable amplitude loading is based on the application of a linear damage summation rule, also known as the Palmgren–Miner’s rule. Even though damage induced by small stress cycles, below the fatigue limit, are often taken into account in design codes of practice by two-slope stress-life curves, the sequential effects of the load history have been neglected. Several studies have shown that linear damage summation rules can predict conservative as well as nonconservative lives depending on the loading sequence. This paper presents experimental results about the fatigue damage accumulation behavior of a structural component made of P355NL1 steel, which is a material usually applied for pressure vessel purposes. The structural component is a rectangular double notched plate, which was subjected to block loading. Each block is characterized by constant remote stress amplitude. Two-block sequences were applied for various combinations of remote stress ranges. Three stress ratios were considered, namely, R=0, R=0.15, and R=0.3. Also, constant amplitude fatigue data are generated for the investigated structural component. In general, the block loading illustrates that the fatigue damage evolves nonlinearly with the number of load cycles and is a function of the load sequence, stress levels, and stress ratios. In particular, a clear load sequence effect is verified for the two-block loading, with null stress ratio. For the other (higher) stress ratios, the load sequence effect is almost negligible; however the damage evolution still is nonlinear. This suggests an important effect of the stress ratio on fatigue damage accumulation.

Articles you may be interested inThe characterization and optimization of NIO1 ion source extraction aperture using a 3D particle-in-cell code Rev. Sci. Instrum.