An alloy-like model based on Y6 and its derivative BTP-M is constructed to fabricate ternary organic solar cells, leading to a best efficiency of 17.03%.

Field-effect transistors based on single crystals of organic semiconductors have the highest reported charge carrier mobility among organic materials, demonstrating great potential of organic semiconductors for electronic applications. However, single-crystal devices are difficult to fabricate. One of the biggest challenges is to prepare dense arrays of single crystals over large-area substrates with controlled alignment. Here, we describe a solution processing method to grow large arrays of aligned C(60) single crystals. Our well-aligned C(60) single-crystal needles and ribbons show electron mobility as high as 11 cm(2)V(-1)s(-1) (average mobility: 5.2 ± 2.1 cm(2)V(-1)s(-1) from needles; 3.0 ± 0.87 cm(2)V(-1)s(-1) from ribbons). This observed mobility is ~8-fold higher than the maximum reported mobility for solution-grown n-channel organic materials (1.5 cm(2)V(-1)s(-1)) and is ~2-fold higher than the highest mobility of any n-channel organic material (~6 cm(2)V(-1)s(-1)). Furthermore, our deposition method is scalable to a 100 mm wafer substrate, with around 50% of the wafer surface covered by aligned crystals. Hence, our method facilitates the fabrication of large amounts of high-quality semiconductor crystals for fundamental studies, and with substantial improvement on the surface coverage of crystals, this method might be suitable for large-area applications based on single crystals of organic semiconductors.

Morphology control is critical to achieve high efficiency CH3NH3PbI3 perovskite solar cells (PSC). The surface properties of the substrates on which crystalline perovskite thin films form are expected to affect greatly the crystallization and, thus, the resulting morphology. However, this topic is seldom examined in PSC. Here we developed a facile but efficient method of modifying the ZnO-coated substrates with 3-aminopropanioc acid (C3-SAM) to direct the crystalline evolution and achieve the optimal morphology of CH3NH3PbI3 perovskite film. With incorporation of the C3-SAM, highly crystalline CH3NH3PbI3 films were formed with reduced pin-holes and trap states density. In addition, the work function of the cathode was better aligned with the conduction band minimum of perovskite for efficient charge extraction and electronic coupling. As a result, the PSC performance remarkably increased from 9.81(±0.99)% (best 11.96%) to 14.25(±0.61)% (best 15.67%). We stress the importance of morphology control through substrate surface modification to obtain the optimal morphology and device performance of PSC, which should generate an impact on developing highly efficient PSC and future commercialization.

A gel is defi ned as a two-component (solid and liquid), continuous, solid-like material with viscoelastic rheological Crystal Growth of Calcium Carbonate in Hydrogels as a Model of BiomineralizationIn recent years, the prevalence of hydrogel-like organic matrices in biomineralization has gained attention as a route to synthesizing a diverse range of crystalline structures. Here, examples of hydrogels in biological, as well as synthetic, bio-inspired systems are discussed. Particular attention is given to understanding the physical versus chemical effects of a broad range of hydrogel matrices and their role in directing polymorph selectivity and morphological control in the calcium carbonate system. Finally, recent data regarding hydrogel-matrix incorporation into the growing crystals is discussed and a mechanism for the formation of these single-crystal composite materials is presented. Future and is researching crystal growth in gels as a means to form nanocomposites.chains form helices (double or single helices) that subsequently aggregate into three-dimensional (3D) bundles, forming a porous network with fi brous characteristics (Figure 1 a,b). [ 82 , 83 ] Both the gelling and melting temperatures can be tailored by chemical modifi cation such as partial hydroxyethylation. [ 84 ] The mechanical behavior of agarose gels is sensitive to molecular weight and concentration [ 85 ] as well as chemical modifi cation.

Single crystals are usually faceted solids with homogeneous chemical compositions. Biogenic and synthetic calcite single crystals, however, have been found to incorporate macromolecules, spurring investigations of how large molecules are distributed within the crystals without substantially disrupting the crystalline lattice. Here, electron tomography reveals how random, three-dimensional networks of agarose nanofibers are incorporated into single crystals of synthetic calcite by allowing both high- and low-energy fiber/crystal interface facets to satisfy network curvatures. These results suggest that physical entrapment of polymer aggregates is a viable mechanism by which macromolecules can become incorporated inside inorganic single crystals. As such, this work has implications for understanding the structure and formation of biominerals as well as toward the development of new high-surface area, single-crystal composite materials.