NiTi shape memory alloys (SMAs) are used in a broad range of biomedical applications because of their unique properties including biocompatibility and high corrosion and wear resistance as well as functional properties such as superelasticity and the shape memory effect. The combination of SMAs and additive manufacturing can lead to revolutionary changes to the uses of SMAs in the biomedical industry. This article discusses the potential biomedical applications of NiTi that benefit from the AM process. We share the lessons learned in processing NiTi alloys with a focus on the laser powder bed fusion (LPBF) technique. The manufacturability, build quality, stable phases and transformation temperatures, microstructure, thermomechanical properties, microstructure tailoring, and functional properties of NiTi alloys produced via AM processing are reviewed. Current challenges such as expanding the process window, controlling the chemistry, and the performance and property responses are discussed, and potential opportunities including alloy design are discussed.

No abstract

The use of titanium bone fixation plates is considered the standard of care for skeletal reconstructive surgery. Highly stiff titanium bone fixation plates provide immobilization immediately after the surgery. However, after the bone healing stage, they may cause stress shielding and lead to bone resorption and failure of the surgery. Stiffness-modulated or stiffness-matched Nitinol bone fixation plates that are fabricated via additive manufacturing (AM) have been recently introduced by our group as a long-lasting solution for minimizing the stress shielding and the follow-on bone resorption. Up to this point, we have modeled the performance of Nitinol bone fixation plates in mandibular reconstruction surgery and investigated the possibility of fabricating these implants. In this study, for the first time the realistic design of stiffness-modulated Nitinol bone fixation plates is presented. Plates with different levels of stiffness were fabricated, mechanically tested, and used for verifying the design approach. Followed by the design verification, to achieve superelastic bone fixation plates we proposed the use of Ni-rich Nitinol powder for the AM process and updated the models based on that. Superelastic Nitinol bone fixation plates with the extreme level of porosity were fabricated, and a chemical polishing procedure used to remove the un-melted powder was developed using SEM analysis. Thermomechanical evaluation of the polished bone fixation plates verified the desired superelasticity based on finite element (FE) simulations, and the chemical analysis showed good agreement with the ASTM standard.

In this study, the effect of the addition of Hf on the oxidation behavior of NiTi alloy, which was processed using additive manufacturing and casting, is studied. Thermogravimetric analyses (TGA) were performed at the temperature of 500, 800, and 900 °C to assess the isothermal and dynamic oxidation behavior of the Ni50.4Ti29.6Hf20 at.% alloys for 75 h in dry air. After oxidation, X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy were used to analyze the oxide scale formed on the surface of the samples during the high-temperature oxidation. Two stages of oxidation were observed for the NiTiHf samples, an increasing oxidation rate during the early stage of oxidation followed by a lower oxidation rate after approximately 10 h. The isothermal oxidation curves were well matched with a logarithmic rate law in the initial stage and then by parabolic rate law for the next stage. The formation of multi-layered oxide was observed for NiTiHf, which consists of Ti oxide, Hf oxide, and NiTiO3. For the binary alloys, results show that by increasing the temperature, the oxidation rate increased significantly and fitted with parabolic rate law. Activation energy of 175.25 kJ/mol for additively manufactured (AM) NiTi and 60.634 kJ/mol for AM NiTiHf was obtained.

NiTi (Nitinol) is a shape memory alloy with distinctive properties, such as shape memory, superelasticity, biocompatibility, and low density. All these unique properties make NiTi a great candidate in different applications. However, the conventional fabrication of NiTi encounters many challenges that significantly limits the practical applications of the alloy. As a solution, the Selective Laser Melting (SLM) which is an Additive Manufacturing (AM) technique has been recently used for the fabrication of NiTi parts. Although complex geometries can be fabricated directly from CAD files via SLM, different process parameters significantly affect the parts’ quality and must be optimized for each application. In most of the potential applications, NiTi components undergo cyclic loads and therefore its structural fatigue must be fully studied and considered in the design process. However, due to the nature of the SLM process, the fatigue behaviour of SLM fabricated NiTi is different from the conventional ones. In this work, as an initial step, the fatigue behaviour of the SLM fabricated NiTi in the horizontal direction is studied and the reasons for failure have been discussed. To this end, strain-controlled fatigue tests were performed on NiTi dog-bone samples, and fractography was used to analyze the different defects which could cause the failure or scatter in the results.