One‐hundred‐and‐twenty‐eight–section dual X‐ray source computed tomography (CT) systems have been introduced into clinical practice and have been shown to increase temporal resolution. Higher temporal resolution allows low‐dose spiral mode at a high pitch factor during CT coronary angiography. We evaluated radiation dose and physical image qualities in CT coronary angiography by applying high‐pitch spiral, step‐and‐shoot, and low‐pitch spiral modes to determine the optimal acquisition mode for clinical situations. An anthropomorphic phantom, small dosimeters, a calibration phantom, and a microdisc phantom were used to evaluate the radiation doses absorbed by thoracic organs, noise power spectrums, in‐plane and z‐axis modulation transfer functions, slice sensitivity profiles, and number of artifacts for the three acquisition modes. The high‐pitch spiral mode had the advantage of a small absorbed radiation dose, but provided low image quality. The low‐pitch spiral mode resulted in a high absorbed radiation dose of approximately 200 mGy for the heart. Although the absorbed radiation dose was lower in the step‐and‐shoot mode than in the low‐pitch spiral mode, the noise power spectrum was inferior. The quality of the in‐plane modulation transfer function differed, depending on spatial frequency. Therefore, the step‐and‐shoot mode should be applied initially because of its low absorbed radiation dose and superior image quality.PACS numbers: 87.57.‐s; 87.57.C‐; 87.57.cf; 87.57.cm; 87.57.cp; 87.57.Q‐; 87.57.qp; 87.57.uq

Recently, specific computed tomography (CT) scanners have been equipped with organ‐based tube current modulation (TCM) technology. It is possible that organ‐based TCM will replace the conventional dose‐reduction technique of reducing the effective milliampere‐second. The aim of this study was to determine if organ‐based TCM could reduce radiation exposure to the breasts without compromising the image uniformity and beam hardening effect in thoracic CT examinations. Breast and skin radiation doses and the absorbed radiation dose distribution within a single section were measured with an anthropomorphic phantom and radiophotoluminescent glass dosimeters using four approaches to thoracic CT (reference, organ‐based TCM, copper shielding, and the combination of the above two techniques, hereafter referred to as the combination technique). The CT value and noise level were measured using the same calibration phantom. Organ‐based TCM and copper shielding reduced radiation doses to the breast by 23.7% and 21.8%, respectively. However, the CT value increased, especially in the anterior region, using copper shielding. In contrast, the CT value and noise level barely increased using organ‐based TCM. The combination technique reduced the radiation dose to the breast by 38.2%, but greatly increased the absorbed radiation dose from the central to the posterior regions. Moreover, the CT value increased in the anterior region and the noise level increased by more than 10% in the entire region. Therefore, organ‐based TCM can reduce radiation doses to breasts with only small increases in noise levels, making it preferable for specific groups of patients, such as children and young women.PACS numbers: 87.53.Bn; 87.57.Q‐; 87.57.qp

Digital imaging with a dynamic flat-panel detector (FPD) is commonly used in clinical practice. However, several factors reduce the accuracy of target tracking in fluoroscopic imaging, including image lag and blurring. There have been several reports focusing on the modulation transfer function (MTF), noise power spectrum (NPS), and detective quantum efficiency (DQE) in different types of FPD. However, there have been no studies comparing image lag and MTF properties in dynamic images obtained with indirect- and direct-conversion FPDs. We investigated the image lag and MTF under several imaging conditions in fluoroscopic images obtained with an indirect-conversion and a direct-conversion FPD system. The measurements of image lag and MTF were obtained under several conditions according to IEC 62220-1-3 standards. We examined whether the image lag and MTF were influenced by the dose level and target movement speed. Indirect-conversion FPD showed dependence on the dose level, which was not observed for direct-conversion FPD. Furthermore, there were large differences in MTF between images of static and moving plate with indirect-conversion FPD in comparison to the differences observed with direct-conversion FPD. These results will be useful for the determination of imaging conditions for target tracking and other types of dynamic imaging.

It is essential to make accurate estimates of the scatter of radiation from the human body when calculating the leakage dose in medical X-ray imaging facilities. The scatter fraction varies with the size and shape of the radiation field in a way that is not exactly proportional to the area of the field. Japanese law quotes values for the scatter fraction that are provided by the National Council on Radiation Protection and Measurements, but these data were obtained 30 years ago, using equipment that differed considerably from that employed nowadays. To date, no attempt has been made to confirm whether these data accurately describe current Japanese equipment. In the present study, we used an ion chamber dosimeter to measure scattered radiation fractions, and new scatter factor data are presented that resolve these problems.

The general method of measuring the half-value layer (HVL) for X-ray computed tomography (CT) using square aluminum-sheet filters is inconvenient in that the X-ray tube has to be set to stationary mode. To avoid this inconvenience, we investigated a new method using copper-pipe filters that cover the ionization chamber (copper-pipe method). Using this method, the HVL can be measured at the isocenter in the rotation modes of CT. We examined the accuracy and reproducibility of the copper-pipe method compared with those of the general method. The effective energy measured using the copper-pipe method correlated well with the general method (y=1.064x, r=0.987), and its error was 1.81±1.38%. The results indicate that the copper-pipe method enables accurate measurement of the effective energy of X-ray CT and is a convenient method suited to all general X-ray equipment as well as all X-ray CT.