Recent soft tissue studies have reported issues that occur during experimentation, such as the tissue slipping and rupturing during tensile loads, the lack of standard testing procedure and equipment, the necessity for existing laboratory equipment adaptation, etc. To overcome such issues and fulfil the need for the determination of the biomechanical properties of the human gracilis and the superficial third of the quadriceps tendons, 3D printed clamps with metric thread profile-based geometry were developed. The clamps’ geometry consists of a truncated pyramid pattern, which prevents the tendons from slipping and rupturing. The use of the thread application in the design of the clamp could be used in standard clamping development procedures, unlike in previously custom-made clamps. Fused deposition modeling (FDM) was used as a 3D printing technique, together with polylactic acid (PLA), which was used as a material for clamp printing. The design was confirmed and the experiments were conducted by using porcine and human tendons. The findings justify the usage of 3D printing technology for parts manufacturing in the case of tissue testing and establish independence from the existing machine clamp system, since it was possible to print clamps for each prepared specimen and thus reduce the time for experiment setup.
The primary goal of this research is the analysis of the biomechanical performances of most common transplants (distal tendon of m.gracilis and upper third of m.quadriceps femoris) used for the reconstruction of the medial patellofemoral ligament (MPFL). The secondary goal is the comparison of the data obtained from the research with the data available in the literature.The research was conducted on 16 samples of the human tendon, of which there are 8 gracilis tendons and 8 quadriceps tendons. Tensile strength is significantly higher in gracilis tendon (26 MPa -92 MPa) than in quadriceps tendon (30 MPa -44 MPa). The extensibility is significantly higher in the quadriceps tendon (10% -15%) than in the gracilis tendon (13% -17%). Regarding stiffness (N/mm) there are no significant differences between the groups of gracilis and quadriceps tendons. The module of elasticity is significantly higher in gracilis tendon (235 MPa -855 MPa) in comparison to quadriceps tendon (239 MPa -361 MPa).The biomechanical characteristics of the distal surface third of the quadriceps tendon are more favourable than the distal tendon of the gracilis which could prove applicable in operative techniques of reconstruction of the medial patellofemoral ligament when choosing a transplant.
The lack of standardization in tissue testing procedures results in a variety of custom-made devices. In the case of the determination of the mechanical properties of tendons, it is sometimes necessary to adapt the existing laboratory equipment for conducting experiments when specific commercial equipment is not applicable to solve issues such as proper gripping to prevent tendon slipping and rupturing, gripping control and manoeuvrability in case of tendon submerging and without contamination of the testing liquid. This paper presents the systematic development, design, and fabrication using 3D printing technology and the application of the double-acting linear pneumatic actuator to overcome such issues. It is designed to do its work submerged in the Ringers’ solution while gripping the tendon along with the clamps. The pneumatic foot valve unit of the Shimadzu AGS-X tensile testing machine controls the actuator thus preventing Ringers’ solution to be contaminated by the machine operator during specimen set-up. The actuator has a length of 60 mm, a bore of 50 mm, and a stroke length of 20 mm. It is designed to operate with an inlet pressure of up to 0.8 MPa. It comprises the cylinder body with the integrated thread, the piston, the piston head, and the gripper jaw. Fused deposition modeling (FDM) has been used as the 3D printing technique, along with polylactic acid (PLA) as the material for 3D printing. The 3D printed double-acting linear pneumatic actuator was developed into an operating prototype. This study could open new frontiers in the field of tissue testing and the development of similar specialized devices for medical purposes.
The paper presents advantages and disadvantages of CAD and BIM technology in the engineering environment. Specific attributes of these technologies have been compared to gain the sense of what they represent in the design and planning process. Through the practical design of the project of the cogeneration plant block, it was noted that CAD environment is more acceptable in the detailed design process. On the other hand, BIM environment, compared to CAD, is less flexible in the process of detailed design but provides a more complete data model at the level of the entire product development process.
Gear tooth side wear in planetary gearboxes represents one of the main reasons for damage occurring in these gears. Wear magnitude is unpredictable and depends on temperature, lubrication, load, material and other random variables. Wear is a non-stationary process which is impossible to describe using a mathematical model, or to accurately assess its intensity, magnitude and distribution along the tooth sides. This paper suggests a probability assessment model for gear tooth side wear, based on experimental tests and a statistical representation of obtained results. Experimental tests of planetary gearbox gears were performed within a closed power circuit, using a previously prepared testing table, and the results of wear probability distribution were analysed. Wear probability distribution was represented using the Weibull distribution model. Obtained results of this statistical analysis have shown good compliance with the experimental ones, hence this model is applicable to all gearboxes. This method represents a considerable contribution to wear probability distribution assessment and can be used in order to assess the work life and elementary reliability of gears.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.