The T2K experiment is a long baseline neutrino oscillation experiment. Its main goal is to measure the last unknown lepton sector mixing angle θ13θ13 by observing νeνe appearance in a νμνμ beam. It also aims to make a precision measurement of the known oscillation parameters, View the MathML sourceΔm232 and sin22θ23sin22θ23, via νμνμ disappearance studies. Other goals of the experiment include various neutrino cross-section measurements and sterile neutrino searches. The experiment uses an intense proton beam generated by the J-PARC accelerator in Tokai, Japan, and is composed of a neutrino beamline, a near detector complex (ND280), and a far detector (Super-Kamiokande) located 295 km away from J-PARC. This paper provides a comprehensive review of the instrumentation aspect of the T2K experiment and a summary of the vital information for each subsystem
The proposed linear electron-positron collider TESLA is based on 1.3 GHz superconducting niobium cavities for particle acceleration. For a center-of-mass energy of 500 GeV an accelerating field of 23.4 MV/m is required which is reliably achieved with a niobium surface preparation by chemical etching. An upgrade of the collider to 800 GeV requires an improved cavity preparation technique. In this paper results are presented on single-cell cavities which demonstrate that fields of up to 40 MV/m are accessible by electrolytic polishing of the inner surface of the cavity.
Electropolishing (EP) in the HF-H 2 SO 4 electrolyte is the most desirable surface treatment for niobium superconducting radio frequency cavities yet demonstrated, in terms of performance and surface finish. However, the efficiency of the electrolyte declines quickly with time (decrease in removal rate, deterioration of the niobium surface, increased sulfur generation). Previous studies at CEA Saclay have highlighted the impact of the water content in EP mixtures rather than the content of dissolved niobium. Knowledge of the electrochemical system was improved thanks to studies using a rotating disk electrode (RDE). Measurements with a RDE give precious information concerning mass transport of the different ionic groups present in the solution. The performed measurements prove that EP is controlled by the diffusion of fluorine ions and the value of the related diffusion coefficient D FÀ was estimated for different mixtures. Electrochemical impedance spectroscopy (EIS) measurements were also performed with different EP mixtures. Both volt ampere metric and EIS measurements prove the central role of fluorine during EP and show that EP mechanisms evolve with the aging of the bath. Another major problem related to electrolytes is the formation of impurities such as sulfur. We have proved that working at a reduced voltage of 5 V does not alter cavity performance and makes it possible to reduce the undesirable particulate contamination in electrolytes and to increase their lifetime.
Reproducible operation at high performances of superconducting cavities is required for linear accelerators. High beta elliptical cavities are thus of concern and, to achieve required performances for such resonators, surface preparation including electropolishing is recommended. We have designed and operate a setup for electropolishing in the vertical position of multicell cavities in order to: (i) obtain high yield with large elliptical cavities for Superconducting Linac (SPL) or European Spallation Source projects; (ii) develop a reference installation demonstrating that this process is appropriate for the large scale treatment of cavities in industry. The setup described here is the first one able to electropolish vertically multicell cavities with circulating acid and high safety standards. This equipment makes it possible to use a wide range of parameters such as voltage, acid flow rate, temperature, and nitrogen injection with an R&D purpose in mind. Optimization is studied using modeling with COMSOL software for different cavities. As examples, we present some results for the 704 MHz high-beta SPL cavity and the 1300 MHz International Linear Collider cavity and show the influence of cathode shape on both acid flow and electric field distribution during the process. Importance of the size of the cavity and first results achieved on single-cell and nine-cell cavities will be discussed.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.